0
What will happen to the wire capacitance if you use parallel wire to one load and one breaker?
Wiki User
∙ 11y ago
The wire will conduct as usual but remember that wires smaller that 1/0 are not allowed to be paralleled according to the electrical code.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the capacity in amperes 20 amp circuit breaker supplying a continuous load?
For a continuous load the circuit breaker is set 25% higher than the load current. So a 20-amp breaker is used with a continuous 16-amp load.
What size breaker do you need for a well pump?
A breaker is based on the amperage that is drawn by the pump motor load. Find the full load amperage of the motor. The wire fed from the breaker has to be rated at 125% of the motors full load amperage. The breaker for motors have to be over sized, usually 250% of the motors full load amps.
Can I add a circuit breaker wired in parrell to a current breaker to reduce the load on the breaker?
No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.
Why your electric dryer makes breaker hot?
If the circuit breaker to a dryer, or to any load, keeps getting hot and trips the breaker, then either the load is pulling too much current or there is a loose connection in the breaker or breaker panel. Either condition must be fixed to reduce the risk of fire.
What is the max load on a 30 amp breaker?
The maximum load on a 30 amp breaker is 30 amps at 40 degrees C. If the ambient temperature is higher that 40 degrees C then the breaker will trip at a lower current. Keep in mind the breaker is a dual function device. On a short circuit the magnetic component will trip the breaker instantaneously. If you are designing a branch circuit for a load that is constantly on, code may require you to "derate" the branch by 20 percent so that the ordinary load is not at the rated load of the overcurrent protection.
Effects of stray capacitance in ac fan out?
due to the load gates capacitance values,there is a increased load capacitance on the driving gate
Why use capacitors with crystal oscillator?
There are two kinds of crystal oscillators. One operates at what is called the "series resonance" of the crystal. This resonance is the frequency at which the (AC) impedance between the pins of the crystal is almost zero. The frequency is independent of how much capacitance happens to be in parallel with the crystal - its inside the oscillator and part of the circuit board, etc. But, even frequency that the oscillator runs at.The other kind of oscillator oscillates at "parallel resonance"of the crystal. At this frequency, the impedance from pin to pin of the crystal is almost infinite. This frequency depends on how much capacitance is connected in parallel with the crystal. This parallel capacitance is called "load capacitance". Generic signal-inverter oscillator is this kind of oscillator.The common oscillator connection is for the crystal to be connected from the inverter output to the input. And, there is a capacitor at each end of the crystal to ground. The NET load capacitance is SERIES equivalent value of those two capacitors.PLUS stray capacitance from the circuit board and the guts of the oscillator. Suppose that the crystal is rated for 22pF load capacitance. The stray capacitance is about 7pF. So, that leave 15pF to be made up from discrete external capacitors. If the external capacitors are equal, then their equivalent is half of their individual value. Thus, in this case, we would want a pair of 30pF capacitors.
Can you connect two 3 phase feed cables in parallel to one circuit breaker and if so what will the total output current be?
The answer to the first part of your question is yes but the wire size has to be of a size specified in the electrical code for wires connected in parallel. As for the second part of the question the total current output is governed by the current draw of the load. It is the load current that governs the parallel wire size and the trip capacity of the breaker.
What will happen to the total current if you keep adding bulbs in parallel to the circuit?
Adding more lamps in parallel (across) a line will cause total current to climb. It will keep climbing (increasing) until a load protection device (circuit breaker or fuse) breaks the circuit or until something fails because of excessive current.
Does each load in a parallel have the same circuit?
your moms a load in a parallel
How is a Load applied to a ac generator?
The load conductor is connected to the load side of the generator breaker. Once the generator is up to speed the load breaker is closed and the voltage is then applied to the load.
What happen when a ammeter is placed in parallel with the circuit?
If an ammeter is placed in parallel with a a load on a circuit, the circuit can short out as the ammeter takes the place of the load, flowing freely through the meter. Never measure across a resister or other electronic load with an ammeter. Remember, ammeters are used in series while voltmeters are used in parallel.
What is the capacity in amperes 20 amp circuit breaker supplying a continuous load?
For a continuous load the circuit breaker is set 25% higher than the load current. So a 20-amp breaker is used with a continuous 16-amp load.
Why is it dangerous for connect an alternator with high capacitance transmission line?
It is dangerous because with capacitive load line voltage will increase which cause the line voltage difference and it will not satisfy the parallel operation of the same voltage rating.
What size breaker do you need for a well pump?
A breaker is based on the amperage that is drawn by the pump motor load. Find the full load amperage of the motor. The wire fed from the breaker has to be rated at 125% of the motors full load amperage. The breaker for motors have to be over sized, usually 250% of the motors full load amps.
What happen when 230 V load is connected to 110 V source?
The breaker will more than likely trip. If not then the appliance will not operate properly.
What happens when the circuit is complete and the switches are closed?
*Look at the simple circuit illustrated in Figure A-2. What will happen when only switch S1 is closed? Correct Answer= "Nothing will happen-the light bulb won't light up." <<>> If there is a load in the circuit the load will operate. If there is no load in the circuit and it is complete then a short circuit will occur and something in the circuit will burn open. If the circuit is complete and there is a fuse or breaker in the circuit, then the fuse or breaker will open the circuit.
