0
The short answer, if using copper, is 0 AWG, commonly referred to as 1/0 or "one ought".
Type of wire depends on location & temperature, but in my common scenario I am using 1/0 THHN inside a 2" schedule 40 PVC conduit (3 - 1/0 wires plus a 4 ga bare ground) to run indoors, a distance of about 25 feet from my main panel to a sub for upstairs.
I could go into more detail regarding outdoor, direct burial, grounding, aluminum wire, etc but would need more details.
Wiki User
∙ 15y ago
Wiki User
∙ 12y ago2 AWG wire in copper and 1/0 (one ought) in aluminum.
Wiki User
∙ 13y agoIn copper 1 AWG in aluminum 2/0 (Two Ought).
Wiki User
∙ 8y agoA #2 AWG copper conductor with a insulation factor of 90 degrees C is rated at 130 amps.
Wiki User
∙ 8y agoA #3 copper conductor with an insulation factor of 90 degrees C is rated at 130 amps.
Wiki User
∙ 10y agoUse AWG 1/0 gauge copper.
Anonymous
1/0
Anonymous
2/0
Add your answer:
Earn +20 pts
What size ground wire for 100a service?
A 100 amp residential service requires a size #8 copper wire, it should be insulated in green.
What wire size for 100 amp single phase 3 wire commercial service?
2 copper
What is the minimum service size for a 225amp residential service?
A 200 amp service panel with a 60 amp sub-panel.
Do you need to change the wire size going from 100 amp service to 150 amp service?
Yes, the wire size has to be increased. The existing 100 amp service will now probably have a #3 conductor with an insulation factor of 75 or 90 degrees C which is rated for 100 and 105 amps respectively. Increasing to a 150 amp service will use a #1/0 wire size. If you are thinking of an upgrade, skip the 150 amp service and go to a 200 amp panel. New homes are installing 200 amp 42 circuit panels. The extra cost is only reflected in the materials as the labour costs will be the same regardless whether a 150 amp or a 200 amp panel is installed. The wire size for a 200 amp panel is #3/0. With an insulation factor of 75 or 90 degrees C the rating is 200 or 210 amps respectively.
What size aluminum wire for 1200 amp service?
For Service Entrance Cable 600 kcmill (Thousands of circular mils).
Ground wire size for 125 amp service?
six awg
Can you replace a 13 amp 125 volt appliance cord with a 15 amp 125 volt cord?
Yes, no problem at all going to a larger ampacity of wire. Larger size wire yes, smaller size wire no.
What size ground wire for 100a service?
A 100 amp residential service requires a size #8 copper wire, it should be insulated in green.
What size of wire to handle 125 Amp?
AWG # 1/0 copper would normally be used.
What size wire do you need for 100 amp service if you use alunimum?
2AWG.
What wire size for 70 amp service at 240 volt?
4 copper
What wire size for 100 amp single phase 3 wire commercial service?
2 copper
What is the minimum service size for a 225amp residential service?
A 200 amp service panel with a 60 amp sub-panel.
What size wire for 25 amp service with a 200 foot run?
10 guage
Do you need to change the wire size going from 100 amp service to 150 amp service?
Yes, the wire size has to be increased. The existing 100 amp service will now probably have a #3 conductor with an insulation factor of 75 or 90 degrees C which is rated for 100 and 105 amps respectively. Increasing to a 150 amp service will use a #1/0 wire size. If you are thinking of an upgrade, skip the 150 amp service and go to a 200 amp panel. New homes are installing 200 amp 42 circuit panels. The extra cost is only reflected in the materials as the labour costs will be the same regardless whether a 150 amp or a 200 amp panel is installed. The wire size for a 200 amp panel is #3/0. With an insulation factor of 75 or 90 degrees C the rating is 200 or 210 amps respectively.
What size aluminum wire for 1200 amp service?
For Service Entrance Cable 600 kcmill (Thousands of circular mils).
What wire size do you need for a 3phase 90amp 60hz 220v?
Wire size is based on the amperage capacity of the service it is feeding. You tell me the service amps and I can tell you the wire size.
