Eliminate it as for example 25.5 divided by 8.5 is the same as 255 divided by 85 which is 3 in both divisions
The divisor must always be a whole number. If it is not already, then you must multiply both the the divisor and dividend by ten until the divisor is no longer a decimal. For example, let's say you have to divide 1.0/0.5 . The divisor in this case would be 0.5 . To multiply by ten, simply move the decimal over to the right one space. That would leave you with 5.0, but since you have to do it on both sides, the final expression would look like this: 10/5 .
No.
To move the decimal you must move the decimal in the divisor all the way to the right to make it a whole number. Then in the dividend, you move that decimal to the right the same amount of spaces you did in the divisor.
You do not need to, but if you must do the following: if the divisor has n digits after the decimal point then multiply by 10n.
Make the divisor (1.41) a whole number and then divide normally. To make the divisor a whole number, the easiest way is to keep multiplying it by 10 until it becomes a whole number; but remember, division is just like a fraction - whatever you do to the denominator (bottom) you must also do to the numerator (top) - so whatever you do to the divisor (the number by which you are dividing) you must do to the dividend (the number into which you are dividing): 0.5 ÷ 1.41 = 50 ÷ 141 (multiply both by 100) = 50/141 ≈ 0.3546
Unlike dividing by a whole number, dividing buy a decimal number cannot be done directly - the divisor must first be converted to a whole number (and then the division can be done). The easiest way to do this conversion is to keep multiplying the divisor by 10 until a whole number is obtained; however, whatever is done to the divisor must also be done to the dividend, so by whatever the divisor is multiplied, the dividend must also be multiplied.
The divisor must always be a whole number. If it is not already, then you must multiply both the the divisor and dividend by ten until the divisor is no longer a decimal. For example, let's say you have to divide 1.0/0.5 . The divisor in this case would be 0.5 . To multiply by ten, simply move the decimal over to the right one space. That would leave you with 5.0, but since you have to do it on both sides, the final expression would look like this: 10/5 .
No.
To move the decimal you must move the decimal in the divisor all the way to the right to make it a whole number. Then in the dividend, you move that decimal to the right the same amount of spaces you did in the divisor.
No.
You do not need to, but if you must do the following: if the divisor has n digits after the decimal point then multiply by 10n.
In that you carry out exactly the same steps - AND you must determine the correct position of the decimal point.
Make the divisor (1.41) a whole number and then divide normally. To make the divisor a whole number, the easiest way is to keep multiplying it by 10 until it becomes a whole number; but remember, division is just like a fraction - whatever you do to the denominator (bottom) you must also do to the numerator (top) - so whatever you do to the divisor (the number by which you are dividing) you must do to the dividend (the number into which you are dividing): 0.5 ÷ 1.41 = 50 ÷ 141 (multiply both by 100) = 50/141 ≈ 0.3546
220
As you divide and increase the number of decimal places, each zero is a holder of the decimal place. It must be used to take the level of accuracy of the answer to a decimal fraction that is 10 times as small as the previous decimal fraction.
If the remained was bigger than the divisor than the divisor could still be taken out of the remainder
3/50000(simplified) or 6/100000, an easy way to figure out decimals like this is dividing by 10 moves the decimal point back by 1. So starting at 6, the decimal must move 5 places, so dividing 6 by 100000 (6/100000) will make 0.00006. If you must move the decimal forward do the opposite and multiply.