answersLogoWhite

0


Best Answer
Answer for USA, Canada and countries running a 60 Hz power supply service.(LIFE SAFETY WARNING! [disclaimer]

Electricity is dangerous!

You can be injured or killed!

Improper installations can cause fire, injury and death!

Should you be doing this yourself?)

  • This is one of the most commonly asked questions in FAQ forums about electricity and wiring. It must be understood that new appliances will be designed to meet the newest standards.
  • It is not reasonable to expect someone to rewire their home because they need a new dryer or range [stove]!
  • According to the NEC [National Electrical Code], it is now required to isolate the neutral conductor from the appliance frame or chassis.
  • It used to be allowable [and therefore common practice] to use the neutral as a grounding means by incorporating a link between the neutral and the chassis.
  • The answer to this safety issue was to require a separate grounding conductor in the cable feeding the appliance.
  • The NEC allows the replacement of the new four prong cord with a three prong cord for appliance replacements in existing installations only!
  • It is then required, when the cord is thusly replaced, to establish the frame grounding link from the chassis to the neutral.

In the present case, the cord has a 10-50P male cord connector and the receptacle is a 10-50R receptacle device. These are standard NEMA configuration designations. See the following location: http://www.leviton.com/sections/techsupp/nema.htm The "crow-footed" terminals get the hot conductors. "W" gets the neutral.

<><><>

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

Before you do any work yourself,

on electrical circuits, equipment or appliances,

always use a test meter to ensure the circuit is, in fact, de-energized.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

14y ago

Check them with a tester or look in the panel and see if the white goes to hot. If it is a 220 line and wired correctly, black and white are hot and bare is neutral, but without checking you can't know what someone else has done.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: When installing a Y-shaped electric range plug and it has places for three wires and you have a black wire white wire and a bare copper wire so which wire goes where?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where can one purchase electric fire places online?

Electric fire places can be purchased online from a retailer such as Amazon or eBay, Overstock, Tesco, Electric Fire Places Direct and Design The Space.


Where can you find electric winches?

There are many places that provide satisfactory electric winches. One of the most reliable places with the widest spread array of electric winches is Amazon.


When installing a Y shaped electric range plug and it has places for three wires and you have a black wire white wire and a bare copper wire so which wire goes where?

Usually the bottom leg is the ground. It should be marked as such with a g or the universal ground symbol, which is stacked dashes that get smaller from top to bottom. In this instance the white and black are both power legs and go to the two angled legs. Use your meter to verify this.


Why does magnesium and copper sulfate react?

Magnesium is more reactive than copper, so it will displace (swap places) with the copper forming magnesium sulphate and copper.


Where can one find tutorials on installing brick veneer?

There are many different places to find DIY instructions on installing brick veneer. One of the most reliable places to find brick veneer installation videos is YouTube.


What are telecommunication engineer jobs?

Telecommunication engineer jobs are basic circuit designing, developments, and is basically responsible for overseeing in stallions of electric switching systems, copper telephone places, and now days fiber optics.


Is copper found in its pure state?

Yes, in some places naturally occurring "nuggets" of copper can be found.


What are some tips for installing outdoor pendant lighting?

There are a large variety of different tips for installing outdoor pendant lighting. These tips include, but are not limited to, installing it in easy to reach places and keeping electrical part out of the rain.


What country does copper come from?

Copper is sourced from various countries worldwide, with key producers including Chile, China, Peru, the United States, and Australia. Chile is the largest copper producer globally, accounting for a significant portion of the world's copper supply.


Where would one find information on installing a thatched roof?

There are many places where one can find information on installing a thatched roof. One can find information on installing a thatched roof at popular on the web sources such as Roofer 911 and Thatch Co.


Where can I go online to learn about copper clad and how to use it?

You may go to many places online to get this information. Some of these places are www.national.com/rap/Story/0,1562,11,00.html and en.wikipedia.org/wiki/Copper-clad_aluminum_wire


Where can you find copper on HorseIsle version 2?

I am not sure if there is any places in caves where copper can be found. But one way to get it would be to have a ranch and put a copper mine on it for 20,000. This will produce 30 copper nuggets everyday.