No, but for neatness most electricians match the incoming and outgoing sets Code states that the conductors should be wire nutted together, black to black, white to white, ground to ground and pigtails from these connections should be connected under the screws to the receptacle. This way if the receptacle is removed from the circuit the rest of the circuit stays intact. Although pigtailing is the preferred method at all times, the pigtailing requirement of the NEC CODE only applies to multi-wire branch circuits where the neutral is being shared Guess a slight difference between CEC and NEC.
The definition of an outlet in Article 100 of the National Electrical Code book (US) is: "Outlet. A point on the wiring system at which current is taken to supply utilization equipment." You can have a receptacle outlet, lighting outlet, or some other hardwired equipment outlet. <<>> The definition of an outlet in Section 0 (Object, Scope and Definitions) of the Canadian Electrical Code book is: "Outlet. A point in the wiring installation at which current is taken to supply utilization equipment."
Because it is a 220 volt outlet instead of a 120 volt outlet. Now, if this is a standard 120 volt outlet that is reading 209 volts then someone has made a mistake in the wiring. You need to call an electrician to straighten this out.
I have never seen a 100 Volt rated outlet. Usually outlets would be rated for 110 to 120 volts for residential use, or maybe 150 volts. The rating is separate from what voltage the outlet is providing. If your outlet is supplying 100 volts, as measured by an accurate voltmeter, you have some problem in your wiring or a faulty outlet. If there is only 100 volts at the outlet get an electrician to diagnose the problem if you are not completely familiar with home wiring. In general you should never use an outlet that has a voltage or current rating less that the device will consume.
The wiring diagram should be on the motor electrical box cover. If not Google the manufactures name of the motor and usually the website has the wiring diagram for the motor.
In North America there are two standard voltages for the wiring of homes, 120/240 volts.
"feed" is the incoming power in relation to residential wiring.
wiring for the plug for the outlet to the charger?
Outlet: A point on the wiring system at which current is taken to supply utilization equipment.
switch socket outlet
Bad wiring or bad outlet.
The definition of an outlet in Article 100 of the National Electrical Code book (US) is: "Outlet. A point on the wiring system at which current is taken to supply utilization equipment." You can have a receptacle outlet, lighting outlet, or some other hardwired equipment outlet. <<>> The definition of an outlet in Section 0 (Object, Scope and Definitions) of the Canadian Electrical Code book is: "Outlet. A point in the wiring installation at which current is taken to supply utilization equipment."
Go buy a book about household AC power and "How to do Wiring Safely".
the bare copper is always a ground
The definition of an outlet in Article 100 of the National Electrical Code book (US) is: "Outlet. A point on the wiring system at which current is taken to supply utilization equipment." You can have a receptacle outlet, lighting outlet, or some other hardwired equipment outlet. <<>> The definition of an outlet in Section 0 (Object, Scope and Definitions) of the Canadian Electrical Code book is: "Outlet. A point in the wiring installation at which current is taken to supply utilization equipment."
Because it is a 220 volt outlet instead of a 120 volt outlet. Now, if this is a standard 120 volt outlet that is reading 209 volts then someone has made a mistake in the wiring. You need to call an electrician to straighten this out.
I have never seen a 100 Volt rated outlet. Usually outlets would be rated for 110 to 120 volts for residential use, or maybe 150 volts. The rating is separate from what voltage the outlet is providing. If your outlet is supplying 100 volts, as measured by an accurate voltmeter, you have some problem in your wiring or a faulty outlet. If there is only 100 volts at the outlet get an electrician to diagnose the problem if you are not completely familiar with home wiring. In general you should never use an outlet that has a voltage or current rating less that the device will consume.
The wiring diagram should be on the motor electrical box cover. If not Google the manufactures name of the motor and usually the website has the wiring diagram for the motor.