0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is Belgium laminated steel?
This is a method used to make shotgun barrels in the 1800's and early 1900's. Wires or thin steel strips were wrapped around a mandrel and hammer-welded. Belgian laminated would be one of the least expensive types of laminated barrels.
What unit of measure would you use to measure carpet?
You would use area. I would use the meter2. Okay
What would you use to measure a marble?
If I was you i would use millimetres or centimetres.
Who would use the word quadrant?
who would use the word "quadrant"
What would you use to measure the diameter of a marble?
I would use a micrometer. A caliper would do as well.
How do you replace a mandrel?
Answer by:MMH Expert_Jimmy K You should begin by removing the deck from the tractor. if not then elevate using ramps. * Remove the belts and the mandrel guards from the deck. * Block the blade with a strong piece of wood so it can't turn and remove the nut on the mandrel pulley. This is difficult to do without an impact driver. Don't hold the blade with your hand you might get cut. Use an impact driver to remove this nut and the blade bolt if possible. * Turn the deck over and use the wood to block the blade and remove the bolt holding the blade to the mandrel shaft and remove the blade. * You have to remove the jackshaft from the mandrel to drive the bearings out of the mandrel housing. Put the nut on the threads of the mandrel and drive the mandrel shaft out the bottom of the mandrel housing. You can drive the bearings out with a screwdriver. The lower bearing will usually come out of the housing when you drive the shaft out. * Drive the upper bearing into the mandrel housing using a piece of wood on the bearing and tapping the wood with a hammer. The lower bearing is on the jackshaft and will go into the housing when you tighten the nut on the pulley. Reassemble the blades and mandrel cover and reinstall the deck under the tractor.
How did they make guns in the early 1800?
A rod called a mandrel, the size of the bore, was placed in a clamp. Strips of iron or steel were heated in a forge, and wrapped and twisted around the mandrel. When the entire length of the mandrel was covered, the steel strips would be reheated, and hammered to weld them together. When completely welded, the mandrel would be removed. The outside of the barrel would be shaped by filing or grinding, usually in the shape of an octagon. The inside would be ground smooth, and if the firearm was to be a rifle, grooves would be cut inside the barrel with a rifling tool. The barrel would be fitted with a lock to fire the gun, and the barrel and lock secured to the stock.
What kind of animal is a mandrel?
monkey
Did Barbara Mandrel spank her kids?
yes
Where does Barbara mandrel live?
Brentwood TN
Where could one purchase a Mandrel tube bender?
The Mandrel tube bender can be purchased on eBay or Amazon. There are three types of Mandrel tube benders. These include: MK1 Bender (£270), MK3 Bender (£350), MK4 Bender (£475).
How was the rifle made?
Twisting steel around a mandrel
H.S CODE For mandrel?
In order to find a single HS code for your mandrel, you must provide additional details. The more information you can provide, the easier it will be to determine the HS code.
Hollow rivets are assembled on a pin often called a?
called mandrel.
What is a mandrel in exhaust systems?
Simply said, a mandrel is a tool used to shape machines. In mufflers, it is tubing usually made of steel used as a support when bending exhaust pipes. The main reason for this is to reduce the possibility of deformation as much as possible. The mandrel bends with the pipe stretching on the outside of the bend and compressing on the inside ensuring a constant diameter bend that reduces restrictions.
How are grooves put in rifles?
Either with a button die orhammered around a mandrel.
What are the three mandrel sisters?
Country musicians Barbara & Louise; and actress Irlene.
