0
PVC is cheaper but is used differently. PVC is usually baried in ground and emt usually runs exposed. You can use PVC exposed if it is schedule 80 gray PVC electrical conduit. Schedule 40 is for under ground
Wiki User
∙ 12y ago
Wiki User
∙ 10y agoThe prices of PVC conduit seem to be a bit cheaper than steel conduit. PVC is light and lower in cost to produce and manufacture. Depending on the place that the conduit is needed, can determine the type of conduit you need.
Add your answer:
Earn +20 pts
Why 2 different phase wire are not supposed to pass through same conduit?
According to the wording ,2 different phase wires "can" run through the same conduit. Not only can they, but if they are part of the same circuit they must. And in cases where conductors are paralleled, meaning more than one conductor per phase as is common in commercial and industrial installations, you put one conductor of each phase and a neutral, if one exists, and a ground in each conduit. Not doing so, meaning to put all of one phase in one conduit, causes a voltage to be induced into the conduit and a tremendous amount of heat builds up. Even when using pvc or other non-metallic conduit, somewhere along the way you have something metallic and have the same problem. To simplify, you must put all conductors associated with the same circuit in the same conduit.
Will there be a conduit 3?
well based on the ending of conduit 2 i think the 3rd one Will be released soon
What type of conduit is used for 480 volt 3-wire?
Conduit is just a medium to get the wires from one place to another. There is no voltage restrictions in low voltage wiring (750 volts or less). When it comes to conduit fill, electricians are governed by the electrical code conduit fill tables. The conduit is sized to accommodate the conductor size for a specific load.
How is an electrical conduit installed?
An electrical conduit is commonly installed in several steps. The first step would be to carefully plan the position of the conduit and what materials that are required for the surface. Then one should execute the plan with common tools such as a screwdriver.
How many 250 kcmil cable in 5 inch conduit?
ONE
How do you join sealtite and PVC conduit?
Install sealtite connector and use PVC FA connector -- threads on one end and coupling on other end to glue to pipe.
Where can one buy PVC conduit fittings?
Someone looking to purchase PVC conduit fittings can find them at most any local hardware store such as Lowes or Home Depot. Other places that may have this item are eBay, Amazon, Menards, and Hardware World.
Should you use PVC conduit on a house rewire or just lay cables and plaster over?
That's an easy one, using conduit is always a better option, and in most European countries is a requirement. Here in the UK, inferior installation standards look more towards cost than quality. My recommendation.....conduit, all the way, all the time.
Why 2 different phase wire are not supposed to pass through same conduit?
According to the wording ,2 different phase wires "can" run through the same conduit. Not only can they, but if they are part of the same circuit they must. And in cases where conductors are paralleled, meaning more than one conductor per phase as is common in commercial and industrial installations, you put one conductor of each phase and a neutral, if one exists, and a ground in each conduit. Not doing so, meaning to put all of one phase in one conduit, causes a voltage to be induced into the conduit and a tremendous amount of heat builds up. Even when using pvc or other non-metallic conduit, somewhere along the way you have something metallic and have the same problem. To simplify, you must put all conductors associated with the same circuit in the same conduit.
Electrical metallic tubing would be used in an electrical installation because it?
The type of conduit system is governed by two factors. One the code book states what type of system can be places in what specific locations. The second factor is what the electrical engineer specifies that what he wants the conduit system to be on his project. EMT is used in the majority of jobs for industrial and commercial projects. As a conduit system it is easy to install and more circuits can be added to the system very easily abiding by the code book rules for conduit fill.
Where can one find information about conduit fittings?
One can find information about conduit fittings from various sources. Some of those sources are Grainger, Home Depot, Prime Conduit, Steel Conduit and Lowes.
What is the difference between one current carrying conductor in a conduit and a hot and switch leg in a conduit?
In the first part of the question there will be only one wire in the conduit, in the second part of the question there will be two wires in the conduit.
What containment system would best be used to house the conductors for a large number of lighting circuits in one area such as a workshop?
There are a few factors when wiring a workshop. The type of work shop and what is manufactured in it. Whether any types of chemicals or gasses will be present. Overall voltage and amperage that is to be used in the workshop. Whether there are any motor loads that are associated with the workshop.These types of projects usually use a conduit system. The conduit system can be of three types. They can be PVC, EMT or Rigid conduit.In Canada, Teck cable is used in these types of buildings installations. Using this type of a system keeps the labour costs lower than conduit systems.If you want to explain the workshop in full detail by using the Discuss button on the left, a more detailed answer will be given.
Where can one purchase an aluminum conduit?
One could purchase aluminum conduit at home improvement retailers such as Home Depot, Lowe's or Rona. One could also order it through a wholesaler such as American Conduit.
Where can one find some EMT works?
If one is looking to find employment as an EMT there are a wide range of job sites that have listings for EMT positions. One can find these jobs on sites such as Indeed, CareerBuilder and Monster.
If you have a motor that must remain adaptable to several sizes of belts what is the maximum length of flexible metal conduit you can use before the conduit requires fastening?
Adding an extra length of shaft on the existing shaft to take extra pulleys will put an extra load on the bearings supporting the shaft. In the long term this would shorten the life of the bearings. The makers might be able to supply more information like the side-load specification for the bearings. If in doubt support the outer end of the shaft.
Will there be Conduit 3?
well based on the ending of conduit 2 i think the 3rd one Will be released soon
