answersLogoWhite

0

The voltage potential is not high enough through design of the switch when it is open. That is why switches and receptacles have voltage ratings. Put a potential of 10000 volts across an open switch and you will have a piece of charcoal.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What kind of cable is needed to connect a switch to a switch?

cross over cable


What are reasonable safety measures?

Do not work on a wet surface Switch off the electricity when trying to fix something dont over load the socket cover open wires with insulation tape Dont put a carpet over open wires


What starts a car?

The ignition switch completes the circuit of electricity from the battery to the starter that actually turn the engine over and starts it.The ignition switch completes the circuit of electricity from the battery to the starter that actually turn the engine over and starts it.


How a switch controls the flow of electric current?

A switch controls the flow of electric current by opening and closing a circuit. When the switch is closed, it completes the circuit, allowing current to flow through. Conversely, when the switch is open, it breaks the circuit, stopping the flow of current. This on/off mechanism enables the switch to control the flow of electricity to a device or appliance.


What effect would occur if the intermediate switch s3 were replace by a double pole switch?

You seem to be referring about a 3 way lighting circuit. If the cross over switch is replaced with a double pole switch, depending on how the switch was wired into the circuit, the load lamp would either stay on or not light at all. A circuit in a three way configuration has two traveler legs between the two switches The intermediate switch in the circuit just switches the two traveler legs from open to close depending on the position of the other two switched. Google, three way switching, they have many diagrams to work from.


What is the purpose of a crossover RJ45 cable?

You can connect 2 PC`s without the use of a switch with a cross-over cable.


What is a 3 gang 3 way switch?

3 gang switch and you can call it 2-way switch..is a type of swithces we are using mostly in the stairs lighting ,that mean you have switch up to the stair and one down to the stair and you can switch the light on from one and switch it off from the other switch and via verse. <<>> There is no such thing as a three gang three way switch,. The nearest thing is a three gang double throw switch. It is used to supply a three phase load from two individual three phase supply sources. This is the type of manual switch that can be used for emergency power switch over from utility to generator. Three way switching uses a single pole double throw switch at each end of the circuit and a cross over switch in the center position. The center switch in a three way lighting configuration is a cross over switch and a double pole double throw switch in that position will not work.


What cable will use for connecting switch to switch?

Most switches and routers these days allow for a standard straight through cable to connect each other. (So any CAT 5e or 6 cable you find at Best Buy will be fine) Older devices (Such as a Cisco 2900xl switch) require a cross over cable to connect like devices such as a switch to switch. These cables can also be found at Best Buy and will be clearly labeled "Cross Over". There are two different standards of straight through cables if making your own. See the related link. To make a cross over cable, wire one end with the A standard and the other with the B standard.


Can a cross over cable be used to connect two unlike network devices such as a PC and a hub?

In general, no, you would not use a cross-over cable to connect a hub/switch/router to a PC. This is because the device itself has cross-over circuitry built into it, and if you used a cross-over cable you would be reversing that process. The net effect is that the transmit signal would connect to another transmit signal, when it should be connected to a receive signal.


Is it possible to link a cross-over connection to a switch or hub?

A crossover cable is used to connect a Hub or Switch to another Hub or Switch - or a PC to another PC.


What are characteristics of a closed figure?

All sides are connected with no open gaps, sides do not intersect or cross over each other.


When to use crossover and straight through?

when you are connecting same devices like computer to computer or switch to switch or router to router to use cross over cable. when you are connecting different devices like computer to switch or computer to router to use straight cable.