0
If pump primes, but only partway, it is usually because the impeller is clogged up with foreign debris (leaves, pebbles, etc). It may be necessary to disassemble the pump and clear out the impeller. One other lazy-man's way that often works is as follows: With pump turned off, close the valve in front of the pump. Remove pump lid, and open air relief valve on top of filter tank. Use a screwdriver to gently rotate the impeller (reaching from inside the pump housing, where your pump basket is). The water in filter tank will run backwards, hopefully pushing the wads of leaves or whatever out. Try this first before disassembling the pump. If pump basket is split/damaged, replace it. I am willing to answer any pool-related questions.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you prime a pool pump?
I have a pump that has a catch basin where leaves and other debris is collected. Two screws hold the top onto the catch basin. When I remove the basket inside, there is water in there along with the basket. With your pump OFF, remove the top to the catch basin. Empty an debris in the basket. Fill a bucket with water and pour the water into this catch basin. (Note that you will only be able to fill it so far, and the rest will go into your pool. As long as you have some water (6-8 inches) in the catch basin, you won't have to worry about running the pump in a dry state.) Replace the basket and the top to the catch basin and screw the top on snugly. Make sure your filter handle is in the position to circulate the water. Turn on the pump. If these instructions do not work, turn off the pump immediately and consult a pool supply company, or a pool repair company for advice. : I agree with the above comment. To improve on it: If you have a valve in front of the pump, close it before opening up the pump. Fill the pump housing up comletely with a water hose/bucket. Open and close the valve as many times as needed until you no longer get the "burping" action. Make sure the water level stays full while you're doing it. This will help get any air out of the lines, so that the pump primes more quickly once you turn the pump back on. P.S. Don't forget the re-open the valve. If pump still does not prime, you may have a leak in the plumbing. Check the nipples going in and out of the pump first to make sure they are not sucking air in. Check any valve bodies for same. Seal any leaks and repair/replace as soon as possible. I can answer any pool-related questions at anjeli-klean.com
What size pump do you need for a 27 ft round pool?
I would recommend 1 HP
How do you find out the gallons per minute fo your pool pump?
It should state the gallons per minute on a label attached to the pump, or on the pump maker's website. To experiment yourself, would involve pumping a measured number of gallons using a stop watch!
How long does it take to drain a 40 thousand gallon pool?
Overnight or same day with the proper size equipment and pump or pumps. K
4 foot deep rectangular pool that measures 23 feet long by 11 feet wide a hose that is able to pump 8.2 cubic feet of water every minute about how long will it take to fill the pool?
The pool is 4ft*23ft*11ft = 1012 cubic feet You can pump in 8.2 cubic feet every minute. So time taken to fill it = 1012/8.2 = 123.4 minutes = 2 hours, 3.4 minutes.
Will air in the pool filter harm the above ground pool pump?
A small amount probably won't but it suggests a leak in the suction line; and it will reduce the pump's ability to prime itself, which is bad. A lot of air won't do the pump or its motor any good. I'm not sure if cavitation is a problem in pumps.
Will it damage the pool pump or filter to let the water level drop?
So long as there is water coming through the pump when it is running it doesnt matter what the water level in the pool is.
Why doesnt your fuel pump work on your 95 Saturn?
Blown fuse, defective fuel pump relay, or the pump itself is defective.
How do you repair harward pool pump from leaking?
If it is the pump seal - replace the seal and other related gaskets. If it is the pump itself - replace the entire pump.
When changing fuel pump in Camry 1992 should you prime the pump?
No reason to, Just cycle the key on and off a few times and it will prime itself.
What is a pump seal for in-ground pool?
Main reason for pump seal (mechanical seals) in a pool pump any pump for that matter is to contain liquid (water in this case) in the pump and hold prime and pressure. Other reasons, lower friction,reliability it can last for years.
How do you prime a winds hied wiper pump 2001 Sierra Z71 GMC?
Just power the pump. If you have W/W fluid in it, it'll prime itself.
How do you get more suction in skimmer for pool vacuum?
you may have to prime your pump Clean or replace the filter.
Why doesnt your fuel pump come on when you turn your key without starting?
Blown fuse, defective fuel pump relay, or the fuel pump itself is bad.
My pool pump has always been on a timer but now when it doesn't run for very long it looses it's prime Why or what can I do to fix this problem?
buy a new pump
Your pool pump is working but it is not pumping water from the pool its like there is a blockage some where what could be the problem?
could be , is the water level above the skimmer/s / are the skimmer baskets clean/? pump may have just lost it's prime. fill pump with water replace lid and restart.
Can air get into pool filter causing it to lose prime if water level in pool is too high?
Yes, air can get into the pool pump causing it to lose prime if you have a leak or crack in the plumbing leading from the pool to the pump. The pool level being too high plays no role, however you should make sure that the pool level is not too high for other reasons, mainly the level is too high, water will leak under your cement causing it to settle. Keep the water level in the middle of the skimmer opening.
