I once put out all circuits in a Hotel In Germany by plugging something in to an outlet in my room. If you are in a Condo there is probably a panel feeding your unit. Your problem might be there instead of the panel in your unit.
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
the answer is no period. You will only make this circuit breaker trip more often. you will need to install another 20 amp circuit or install what is called a piggy back circuit breaker. you can may find this at Lowes or Home Depot or better yet take a circuit breaker out of the electrical panel and go to a electrical distributor.
None! Distribution panel designed to use specific type of circuit breakers. It's a NEC violation to install different type of breaker even it fits perfectly.
Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.
Yes. You'll seldom run every circuit to full capacity. The main breaker will trip if all the individual circuits exceed the 200 amp rating of the main breaker.
There are many ways one can install ge circuit breakers. One can install ge circuit breakers by turning off the power supply, removing the panel cover, testing it for power, and installing it by alining the breaker with the unused panel space.
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
the answer is no period. You will only make this circuit breaker trip more often. you will need to install another 20 amp circuit or install what is called a piggy back circuit breaker. you can may find this at Lowes or Home Depot or better yet take a circuit breaker out of the electrical panel and go to a electrical distributor.
None! Distribution panel designed to use specific type of circuit breakers. It's a NEC violation to install different type of breaker even it fits perfectly.
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
Check the nameplate on the actual breaker. Some breakers are rated for AC or DC. If it doesn't specifically list DC on the nameplate, then no, you should not rely on the breaker to adequately protect the circuit.
A miniature breaker is just two breaker that fit into one breaker slot. These types of breakers are designed to install the same as a full size breaker. Different types of breakers have different mounting configurations to the panels bus bars so installation instructions are not possible without knowing the make and type.
Example sentence - We hired an electrician to at the circuit breaker and install an updated panel.
Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.
Yes. You'll seldom run every circuit to full capacity. The main breaker will trip if all the individual circuits exceed the 200 amp rating of the main breaker.
If you have a light that is not being powered through a circuit breaker or fuse, you should call a qualified electrician to remove this circuit from the panel's bus and install a circuit breaker for it. Without an overcurrent protective device (circuit breaker or fuse) you have a potential fire hazard.
you can use a fuse or circuit breaker