0
The percentage impedance of a transformer is the volt drop on full load due to the winding resistance and leakage reactance expressed as a percentage of the rated voltage.
It is also the percentage of the normal terminal voltage required to circulate full-load current under short circuit conditions
The impedance is measured by means of a short circuit test. With one winding shorted, a voltage at the rated frequency is applied to the other winding sufficient to circulate full load current
Z% = Impedance Voltage x 100
Rated Voltage
Add your answer:
Earn +20 pts
Is 0.900 percent equal to 90 percent?
0.900 percent = 0.90 percent = 0.9 percent = 9/10 percent 0.900 percent = 0.009 0.900 = 90 percent
How do you find a percent of a percent?
1 percent of a percent is 1/10000 or 0.0001; this is the same as saying 1 percent percent. Example: 5 percent percent is 0.0005, so 5 percent percent of 100 is 0.0005 x 100 or 0.05.
What percent of 10 percent of 50 is 25 percent of 100?
Parsing the question: What percent of 10 percent of 50 is 25 percent of 100? What percent of 10 percent of 50 is 25? What percent of 5 is 25? Answer: 500%
What does 60 percent equals as a percent?
60 percent as a percent is 60%
What is 30 percent of 20 percent of 150 percent?
To find 30 percent of 20 percent of 150 percent, you first need to calculate 20 percent of 150 percent. To do this, you multiply 0.20 by 1.50, which equals 0.30. Next, you find 30 percent of 0.30 by multiplying 0.30 by 0.30, which equals 0.09. Therefore, 30 percent of 20 percent of 150 percent is 0.09.
How do you convert percent impedance of transformer to impedance value?
The apparent impedance looking into a transformer from one side will not be the same as looking in it from the other, which is why percent impedance is used. If you are looking from the high voltage winding (I'm labeling #1) to the low voltage winding (#2), you must scale the percent impedance as follows: (% impedance) x (Winding #1 nominal voltage)^2 / (transformer base VA)
What is the most accurate way of measuring percent body fat?
Bio electrical impedance machine
Which is better high input impedance or low input impedance and why?
That depends on the output impedance. In electronic we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance. An input impedance is called also a load impedance or an external impedance. An output impedance is called also a source impedance or an internal impedance.
How to distinguish between characteristic impedance and input impedance?
The characteristic impedance or surge impedance belongs to uniform transmission lines.In electronic gears we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
Input impedance is greater than to load impedance?
In electronic gears we use voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
Is characteristics impedance of a filter is same as output or load impedance?
load impedance
What is analog audio impedance?
To get all the audio voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is at least ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
What is high input impedance?
To get all the voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
Input impedance is high and output impedance is low justify the statement?
To get all the voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is more than ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
In a multistage amplifier input impedance is high and output impedance is low justify the statement?
no. input impedance is low & output impedance is high
What means Impedance?
To get all the audio voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is at least ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
Why is output impedance kept low?
To get all the audio voltage from a source to a target without loss you need voltage bridging, that is a relative low output impedance to a higher input impedance. Usualy the input impedance is at least ten times higher then the output impedance.An input impedance is called also a load impedance or an external impedance.An output impedance is called also a source impedance or an internal impedance.
