Yes. The voltage of 120 volts is a nominal figure. The utility company has a plus or minus tolerance from 110 to 120 volts. This tolerance is based on the figure of 115 volts.
There are two types of thermostats. One is a line voltage stat. This is in effect a switch and when turned to the off position the voltage is interrupted and the heater will not operate. The other type of stat is low voltage. There will be a relay in the baseboard heater that the thermostat is connected to. With this type if installation to turn the power completely off you will have to turn the breaker off that feeds the circuit.
Go to your power panel and look for two pole breakers. If there are any 20 amp two pole breakers there is a good chance that they are for the baseboard heaters. Switch this breaker off and turn your thermostat up. If the baseboard heaters do not come on and get hot then this is the supply for them. A two pole breaker is supplying 240 volts to the heaters. Most likely there will be more that one heater on the circuit. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Amps and Watts measure different things. An Amp is a measure of electrical current and a Watt is a measure of Power. Which ever device draws the higher amperage will be the one that uses more electricity! Hence the 240 watt heater draw less amps even though it uses more watts: Volts Watts/Electical Current Amps/Power example heater 240 volt draws 2000/1000 watts - but uses 8.3/4.2 amps example heater 120 volt draws 1500/750 watts - but uses 12.5/6.3 amps
first of all you buy a double pole unit thermostat which should come with the mounting plate and thermostat and it should have 4 wires 2 red 2 black okay now you join the red to the red power wire and black to the black power wire and the 2 remaining wires which should be a red and black can be joined to the red and black wires on your heater .....now you should be good to go ............LEE48
The two most important ratings for an electrical heater are its rated power and its rated voltage, and these will be printed on a 'nameplate' fixed somewhere on the heater (e.g. '3 kW at 230 V').For the heater to operate at its rated power, it must be subject to its rated voltage. In the above example, the heater will only operate at 3 kW if it is supplied with 230 V.If you know the heater's power (P) and its voltage (U), then you can calculate the rated current (I) it will draw from the supply, using the equation: I = P/U.You can also determine its resistance (R), using the equation R = U2/P.
To replace an electric baseboard heater, first turn off the power to the heater at the circuit breaker. Remove the cover and disconnect the wires. Unscrew the heater from the wall and remove it. Install the new heater by screwing it into place, connecting the wires, and replacing the cover. Finally, turn the power back on and test the new heater to ensure it is working properly.
To safely and effectively install an electric baseboard heater plug in, follow these steps: Turn off the power to the area where you will be installing the heater. Choose a location near an electrical outlet and ensure there is enough clearance around the heater. Mount the heater securely to the wall according to the manufacturer's instructions. Connect the heater to the electrical outlet using a properly rated plug and cord. Turn the power back on and test the heater to ensure it is working properly. It is recommended to consult a professional electrician if you are unsure about any step in the installation process.
To replace a baseboard heater thermostat, first turn off the power to the heater at the circuit breaker. Remove the cover of the existing thermostat and disconnect the wires. Install the new thermostat by connecting the wires according to the manufacturer's instructions. Secure the new thermostat in place and replace the cover. Finally, turn the power back on and test the thermostat to ensure it is working properly.
The steps involved in baseboard heater replacement include turning off the power, removing the old heater, measuring and purchasing a new heater, installing the new heater, connecting the wiring, and testing the heater to ensure it is working properly.
To properly install baseboard heater wiring in your home, follow these steps: Turn off the power to the circuit where you will be installing the baseboard heater. Measure and cut the appropriate length of electrical cable for the installation. Strip the insulation from the ends of the cable and connect it to the heater according to the manufacturer's instructions. Secure the cable to the wall using cable staples or clips, making sure to leave some slack for flexibility. Connect the other end of the cable to the electrical panel, following proper wiring techniques. Turn the power back on and test the heater to ensure it is functioning correctly. It is recommended to consult a licensed electrician if you are unsure about any step in the installation process.
To properly wire a baseboard heater for optimal performance and safety, follow these steps: Turn off the power to the circuit where the heater will be installed. Use the correct gauge wire for the heater's voltage and amperage requirements. Connect the wires to the heater according to the manufacturer's instructions. Use wire connectors to secure the connections and prevent them from coming loose. Install a dedicated circuit breaker for the heater to prevent overloading the circuit. Test the heater to ensure it is working properly before use. By following these steps, you can ensure that your baseboard heater is wired correctly for optimal performance and safety.
To wire a baseboard heater properly, first turn off the power to the circuit. Connect the heater's wires to the corresponding wires in the electrical box using wire connectors. Make sure to follow the manufacturer's instructions and local electrical codes. Finally, secure all connections and turn the power back on to test the heater.
The best way to troubleshoot a malfunctioning thermostat for a baseboard heater is to first check the power supply, then inspect the thermostat settings and connections, and finally consider replacing the thermostat if necessary.
To safely remove a baseboard heater from your home, first turn off the power to the heater at the circuit breaker. Then, remove the cover and disconnect the wiring. Next, unscrew the heater from the wall and carefully lift it out. Be sure to follow all safety precautions and consider hiring a professional if you are unsure.
To effectively remove a baseboard heater from a room, first turn off the power to the heater at the circuit breaker. Then, remove the cover panel and disconnect the electrical wires. Next, unscrew the heater from the wall and carefully lift it out. Finally, patch up any holes left in the wall and dispose of the heater properly.
Your thermostat is just a temperature switch. A switch just breaks the circuit to stop the current from flowing. When you set a position on the thermostat you are telling the switch when to come on and when to shut off depending on the room temperature. If it is set to low then the base board heater will not come on until the low set-point is reached. When the room warms up to above the set-point the baseboard heater will shut off. If your concern is about a 240 volt baseboard heater and just a single pole on the thermostat do not worry. Breaking one leg of a 240 volt circuit will stop the current flow and the heater will not operate.
To effectively remove a baseboard heater, first turn off the power to the unit. Then, remove the cover and disconnect the electrical wiring. Next, unscrew the unit from the wall and carefully lift it out. Finally, patch up any holes left in the wall from the removal.