0
Yes.
But the NEC requires that your first disconnect be installed as close as practical to where the service enters the building. So if the bedroom isn't where the service enters the home, you will have to install a stand-alone disconnect where it does and then wire to your panel.
Add your answer:
Earn +20 pts
Can you put a breaker panel in a hall?
Yes a breaker panel can be located in a hall. In fact a lot of apartments have them in that location just as you come in the main door to the apartment.
What type panel does a 4 pole breaker require?
The panel and breaker have to be of the same manufacturer. This way the breaker will fit into the panel. If the panel has a push in bus bar, the breaker must also be the type to accept the bus bar. If the bus bars in the panel are of the bolt in type then the breaker also has to be a bolt in breaker.
Will cutler hammer breaker panel fit a GE breaker?
No, a Cutler Hammer will not work in a GE panel or vice versa.
Can you put a 60amp breaker and a 50amp breaker on a 60amp subpanel just as long as they are not being used at the same time?
You can. Using these size breakers in a 60 amp sub panel might be pushing the limit for breaking the sub panels feeder breaker. The breaker feeding the sub panel will have to be no bigger than 60 amps because of the main bus bar capacity of the sub panel. It would be better to install a 100 amp sub panel and then there would be a bit of a buffer and you will have the ability to add additional small load circuits.
What size breaker do you use for a 100 amp sub panel?
A 100-A sub-panel would be fed from a 100-A breaker.
Can you put panel in bedroom?
yes
Can you put a breaker panel in a hall?
Yes a breaker panel can be located in a hall. In fact a lot of apartments have them in that location just as you come in the main door to the apartment.
What type panel does a 4 pole breaker require?
The panel and breaker have to be of the same manufacturer. This way the breaker will fit into the panel. If the panel has a push in bus bar, the breaker must also be the type to accept the bus bar. If the bus bars in the panel are of the bolt in type then the breaker also has to be a bolt in breaker.
How do you prevent Frost behind breaker panel?
To prevent frost behind a breaker panel, ensure proper insulation is installed around the breaker panel to maintain consistent temperature levels. Additionally, seal any gaps or openings around the panel to prevent cold air from entering and causing condensation. Regularly check for any signs of moisture buildup and address any issues promptly.
My seimans elect panel box let me put in tandem breakers?
I wnt to install a tandem breaker but my panel box won't let me. Why?
What is installing a circuit breaker?
It is inserting a breaker into a service panel.
What breaker to use in a bedroom that holds up to 15 amps with 120v?
15 amp breaker.
Can you wire 2 bedroom on 1 breaker?
You can't wire 2 beedrooms on one breaker.
Will cutler hammer breaker panel fit a GE breaker?
No, a Cutler Hammer will not work in a GE panel or vice versa.
Can you put a 50 amp beaker in a 60 amp panel?
No, it is not safe to put a 50 amp breaker in a 60 amp panel. Breakers need to be sized to match the panel's capacity to prevent overheating and potential fire hazards. It is important to always use breakers that are compatible with the panel's amperage rating.
What breaker can I use if I dont have a westinghouse breaker?
If you don't have a Westinghouse breaker, you should use a breaker that is compatible with your electrical panel. Consult the panel's specifications or a qualified electrician to determine the appropriate replacement breaker for your specific panel. Using an incompatible breaker can be dangerous and may violate electrical codes.
Can you put a 60amp breaker and a 50amp breaker on a 60amp subpanel just as long as they are not being used at the same time?
You can. Using these size breakers in a 60 amp sub panel might be pushing the limit for breaking the sub panels feeder breaker. The breaker feeding the sub panel will have to be no bigger than 60 amps because of the main bus bar capacity of the sub panel. It would be better to install a 100 amp sub panel and then there would be a bit of a buffer and you will have the ability to add additional small load circuits.
