0
Add your answer:
Earn +20 pts
Can a 220 Volt well motor be added to a 200 amp box or does it need its own box?
The well pump breaker is installed in two slots in your breaker box. You then run the correct size cable for the amperage of the pump to the area where the pressure tank is located. install a breaker or disconnect on the wall near the pressure tank and then connect the low pressure switch to the disconnect. Connect the pump to the low pressure switch.
Cost to install 1200 Amps Circuit Breaker?
1200 Amps is a huge breaker. Typical houses might have between 100 and 200 Amp service. Since this would have to be a very unique installation you would have to provide a lot more information before cost could be computed. You also have to indicate who is supplying the breaker which would be a significant cost on its own.
Gauge wire needed for 8 amp sump pump?
you will need wiring that is at least 10 amp rated wire or higher. If you really needed to ask you might want to call an electrician Electrician here, be the pump 120 volts or 240 volts a #14 wire will handle the situation. Longer runs of 75 feet you should go to a #12 wire to compensate for voltage drop. The pump should be on its own separate circuit with a 15 amp breaker. A two pole 15 amp breaker if the pump is 240 volts.
Can I wire nut two black wires together and hook 1 to a breaker?
Not according to the electrical code. It requires each separate circuit to be fed individually from its own breaker. If allowed it would reduce the total capacity of each circuit from one amp per outlet to a half amp per outlet if the circuit was fully loaded.The work around in situations like this is to use a tandem breaker which gives you the capacity of two complete circuits and only using one breaker slot in the distribution panel board.
Can you use wire nuts inside a main breacker panel or to extend a new to an old knob to romax to breacker to include 220 volts?
There should be no joints like that inside the breaker panel. I'm pretty sure the NEC, or in my case the Canadian Electrical Code prohibits having any wire nuts/marrettes in it. Any such joints should be done outside the breaker panel in it's own junction box.
Does lg own whirlpool?
NO. LG is based out of Korea and is its own company. Whirlpool is made in America.
How do you become a whirlpool products distributor or dealer?
The easiest way to find this information is to contact the Whirlpool Corporation. You will want to start your own business selling these appliances, so you will need small business experience.
Do air conditioners need there own circuit breaker?
It is recommended for air conditioners to have their own dedicated circuit breaker to ensure proper power supply and prevent overloading the circuit. This can also help in troubleshooting electrical issues that may arise with the air conditioner.
Will a GE pedestal fit a Whirlpool?
No, each manufacturer taylors the pedestal to their own brand
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
In what foreign companies did Whirpool own stakes?
Whirlpool owned stakes in Inglis of Canada and in an Italian company. Whirlpool also developed joint ventures with companies in India, Mexico, and the Netherlands
Can you install 220 volt outlets in American homes?
Yes. It is best to run a line from main breaker box to a separate 220V box with it's own breaker. You will need a licensed electrician to install if you are'NT comfortable doing this type of installation yourself.
How do you install electrical wiring for room aircon?
More information is needed, maybe a lot more. Depending on its size you may need a new circuit for it. If you trip the breaker then don't use it and get a new circuit installed for it on its own breaker. You are probably talking about a window unit. If it is a simple 5000 BTU unit you can probably plug it into the nearest receptacle. If you trip the breaker then you need to run a new circuit for it. If it is much larger you may need to run a new circuit. If it is a 240 volt unit then you need a new circuit.
Can you daisy chain breaker panels?
No, breaker panels should not be daisy-chained as it can create a safety hazard and overload the system. Each breaker panel should have its own dedicated circuit from the main service panel.
What refrigerator brand names did Whirlpool own by 2002?
It owned the Whirlpool, KitchenAid, Roper, Coolerator, and Speed Queen brand names, and many of its appliances were sold under the Kenmore name through Sears, Roebuck and Co.
Can you put a 20amp water pump and a 30 amp water heater on a 50amp breaker?
No, it is not safe to put a 20 amp water pump and a 30 amp water heater on a 50 amp breaker. The total amperage exceeds the capacity of the breaker, which can lead to overheating, tripping, or even a fire hazard. It is recommended to have separate dedicated circuits for each appliance to ensure safety and proper functionality.
Can you increase the power supply to a circuit breaker in a condo It's a townhouse style condo We have our own circuit breaker in the garage but we need 150amps and only have 90amps?
Before making any changes to circuit breakers, make certain that the breaker does not exceed the capacity of ANY current carrying wire in the circuit. If you attempt to increase the size of the breaker in your condo, and exceed the capacity of the wire that is fed from that breaker, you WILL burn down the condo and when the fire department investigates the fire and finds out what you did, the association will be quite upset with you. Plus, it's against the law. If you need to make that kind of change to your electrical wiring, contact a qualified electrician to discuss options. You will also need approval of the Condo Association in most situations like this.
