0
Your main concern in installing anything near a water line is to avoid accidentally driving a nail or screw into the pipe, causing a leak. Therefore it is prudent to allow a separation of at least a few inches. Other than that, there is no reason why a light fixture cannot be close to a water line. The wires are insulated, so they are not going to short circuit as a result of the metal pipe.
Add your answer:
Earn +20 pts
Why must an electrical circuit be closed for energy to flow?
The electrical circuit is analogus to the water piping system. The word "close" means connection of a switch to get a complete circuit and to a water system you open the valve to let the water flows. Likewise if there is a connection the electrical energy flows. If "open" that means disconnected and for water piping system closing the valve to stop water flows. Therefore "close" for electrical ciruit means "open" for water piping system, and "open" for the former means "close" for the latter.
Will your electric water heater blow up if your water is turned off?
Only if you leave the burners or elements on. -If water stops, close gas line or switch off breaker for tank.
How can water supply electricity?
Water can supply electricity in usually one reason - the water wheel, or it's close cousins. The water pushes on the wheel, and turns the water wheel. As the wheel spins, it creates mechanical energy. This mechanical energy is fed through a converter, which turns it into useable electricity. It is the same concept as wind with a wind turbine.
List several examples of how electrical energy and light energy are useful to you?
Electrical energy and light energy are useful to me in a variety of ways from the machines used to make the food you eat to the energy used to purify the water you drink. The clothes you wear are even dyed different colors from the light energy alone.
Do you need gfci on bathroom fan?
No. The only thing required to be gfci protected is a receptacle. I've never understood why light fixtures, fans, and other appliances do not required protection around so much water, but they do not. They should, however, be listed for damp locations.
Why is there water in your tail light?
Bad seal in light fixture
What is a low flow fixture?
A low flow fixture is a plumbing fixture, such as a showerhead or faucet, that is designed to reduce water consumption by restricting the flow rate of water. This helps to conserve water and reduce water usage without sacrificing performance.
Is it ok to have water in the bottom half of the light fixture in an underwater pool light fixture?
No. The specifications and design of underwater lighting is to be completely waterproof. You have a leak in the seal and it should be looked after as soon as possible. Once the water reaches the bulb it will most likely break and then trip the GFCI that the fixtures should be connected to. Fix the leak now to save yourself aggravation later.
What is a fixture opening?
A fixture opening refers to the space or connection point where a plumbing fixture, such as a sink, toilet, or shower, is installed in a building's plumbing system. It is where the fixture is connected to the water supply and drainage pipes.
What does the electrical terminology of the word - fixture - mean?
"Fixture" generally refers to things permanently attached to the structure. A light fixture would be one example, screwed to the wall or ceiling. The light fixture, also called a luminaire, would include devices for holding the lighting elements, supplying electricity to them, enclosing the connections for safety, and means for attaching it to the electrical supply permanently. A "fixture" could, in theory, dangle from a cord permanently attached to a suitable support. For contrast, a cord-connected device would not be a fixture. In fact, it is often illegal to use cord and plug on any appliance that is permanently attached (e.g., screwed in or with water pipes attached).
Is a pool spotlight different from a regular outdoor flood light?
yes a pool light is typically a sealed unit. this is to prevent water from entering the light and coming in contact with the electrical components of the light. if water were to enter the light it could damage the light fixture and also trip the light breaker or gfci. in addition in some situations if the light were not installed correctly/electrically protected correctly (with breaker and gfci) could cause a dangerous situation to bathers. to change the light bulb in a pool light fixture the light fixture must be brought above the waters surface and the lense with lense gasket removed bulb changed then lense with lense gasket replaced and the light reinstalled in the light niche in the wall of the pool below the waters surface. you must also use the appropriate bulb for the light fixture. this is not as simple as just picking up a bulb from home depot and threading it in as you would do with an outdoor flood light. light repairs should only be performed by a trained pool professional as it could be dangerous if not done correctly.
What is the most likely cause of an underwater pool light continually tripping GFI if it does not appear to be an overloaded circuit?
The most likely cause is water leakage into the light fixture, causing a ground fault. Make sure the fixture is properly sealed and there are no cracks or damage that could allow water to enter. If the issue persists, consult a professional electrician to inspect the wiring and connections.
Why would you throw water at a mirror in the dark?
Cause during your back swing you knocked out the light bulb in the low hanging light fixture!The reason you were throwing the water at the mirror in the first place????? You were having a drink and saw a spider on the mirror and you suffer from arachnophobia!
Why is a light shorting out?
A light may be shorting out due to loose connections, a faulty bulb or fixture, water damage, or a wiring issue. It is important to diagnose and fix the problem promptly to avoid potential safety hazards.
Why do you have running cold water but no running hot water?
1- valve closed 2- pilot light not lit and thus no flame to heat the water (electric not working) 3- someone forgot to run a H/W line to a fixture
What is floor washing water fixture unit?
Got no clue
How do you get rust from bathroom light fixture?
You can remove rust from a bathroom light fixture by scrubbing it with a mixture of equal parts vinegar and baking soda. Let the mixture sit for a few minutes and then scrub the rust away using a cloth or sponge. Rinse the fixture with water and dry it thoroughly.
