answersLogoWhite

0

Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you disconnect a light switch and outlet that are tied together?

If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.


How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?

You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.


How do you wire multilple power outlets and light?

Power into the first outlet and out to all other outlets, black to gold and white to silver screw, ground wires to ground screw. From the outlet closest to the light switch run power from that outlet up to the switch box. Run another wire from the switch box up to the light. In the switch box tie all the whites together under a wire nut and push them back into the box. Tie all the ground wires together and connect that to the ground screw on the switch. Connect the 2 black wires you have left to the 2 screws on the switch. Does not matter which if you only have power in and power out to the light.


How can i find out if the live wires i found in my wall are for a light switch or an outlet?

Use a voltage tester held next to the wire. Turn the switch off. If the tester stops beeping then the wires are on that switch.


Why won't my Light turn off at switch?

Presuming the switch worked at one point and just stopped working it is likely that the switch has failed in a normally closed position. The only other possibility is that somehow you have a wire problem whereby the hot side of supply is connected to the load side of the switch. This could be caused by an exposed wire in the switch receptacle. Suggest you turn off power at breaker and replace switch as a start. When you have the switch removed from the receptacle, with wires still connected see if switch works. If it does it could still be bad, but examine the wires around switch and see if you have any exposed wire that could be touching the load side of the switch (Side connected to the light).

Related Questions

How do you wire a light switch to an outlet?

To wire a light switch to an outlet, you need to connect the hot wire from the outlet to the hot terminal on the switch, and then connect the hot wire from the light fixture to the other terminal on the switch. Make sure to turn off the power before starting and follow all safety precautions.


How do you Wire a light from a switched outlet?

See: "How can you re-wire a wall switch that controls an outlet to control a ceiling fan?" (Follow the link below.) The procedure is the same whether the new device is a light fixture or a ceiling fan.


How do you wire a light switch and outlet together?

To wire a light switch and outlet together, you will need to connect the hot wire from the outlet to the hot terminal on the switch. Then, connect the neutral wire from the outlet to the neutral terminal on the switch. Finally, connect the ground wires from both the outlet and switch to the ground terminal on the switch. Make sure to turn off the power before starting and follow all safety precautions.


What is the correct wiring diagram for a light switch and outlet in a residential setting?

In a residential setting, the correct wiring diagram for a light switch and outlet involves connecting the hot wire to the brass terminal on the outlet, the neutral wire to the silver terminal on the outlet, and the ground wire to the green terminal on the outlet. The hot wire is then connected to the brass terminal on the light switch, and the neutral wire is connected to the silver terminal on the light switch. Make sure to turn off the power before attempting any wiring work.


How can I add an outlet to a light switch?

To add an outlet to a light switch, you will need to run a new electrical wire from the switch to the location where you want the outlet. This involves turning off the power, removing the switch, connecting the new wire, and installing the outlet. It is recommended to consult a licensed electrician for safety and proper installation.


How do you disconnect a light switch and outlet that are tied together?

If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.


Can you change an electrical outlet into a switch for a light?

Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.


How can I wire a GFCI outlet with a light switch according to a diagram?

To wire a GFCI outlet with a light switch according to a diagram, follow these steps: Turn off the power to the circuit at the breaker box. Connect the incoming power supply wires to the LINE terminals on the GFCI outlet. Connect the wires leading to the light switch to the LOAD terminals on the GFCI outlet. Connect the wires from the light switch to the appropriate terminals on the switch according to the diagram. Turn the power back on and test the outlet and light switch to ensure they are working properly.


How do you wire a two way switch one controls the outlet the other the outdoor light with a pigtail?

You need two separate switches. You can get two switches that are in the same form factor as a single switch (2 gang switch). You use one switch for the outlet and the other for the light. You switch the black wires which are "hot".


How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?

You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.


What is the correct wiring diagram for a light switch and outlet on the same circuit?

The correct wiring diagram for a light switch and outlet on the same circuit involves connecting the hot wire to the brass terminal on the outlet, the neutral wire to the silver terminal on the outlet, and the hot wire to the brass terminal on the light switch. The neutral wires should be connected together. It is important to follow all safety guidelines and consult a professional if needed.


How do you wire an outlet to a switch?

To wire an outlet to a switch, you need to connect the hot wire from the outlet to one terminal on the switch, and then connect another wire from the other terminal on the switch to the outlet. This allows the switch to control the flow of electricity to the outlet. Make sure to turn off the power before attempting any electrical work.