0
What else can I help you with?
Can i run a 240 volt water heater on 120 volt?
No. A water heater requires a 240 volt connection and cannot be re-wired to run on 120 volts. There isn't enough amperage in 120 volts to power the heating rods that are inside.
How are loads or power-consuming devices usually wired?
Loads or power-consuming devices are usually wired
How are furnace switches wired?
Furnace switches are typically wired using a standard electrical method where a switch is connected to the furnace's power supply. The switch is usually installed in line with the power source, allowing it to interrupt the electrical flow to the furnace when turned off. This setup typically involves connecting the hot wire from the power supply to one terminal of the switch and a wire leading to the furnace to the other terminal. Additionally, a neutral wire may also be connected to complete the circuit, and grounding is essential for safety.
What is the drawing symbol for a baseboard heater?
Hot----------------/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\------------Common This is the symbol for any electric heater. The controlling device would be noted as --------I I-------- denoting the Normally Open contacts of a relay and the would be wired to the Hot side. I cannot show you the symbol for a thermostat due to keyboard limitations.
How do you ad and extra switch and light to the same 2 by 4 box?
There are multiple ways to wire a switch. If power is fed into the switch box, a second light would be wired one way, if power is fed into the light box, the second light would be wired a different way. This seems like it would be a task better given to a qualified electrician or local handyman.
If the heater fan doesn't work and all fuses are good as is the blower motor relay what's the problem with the heater fan?
Motors do go bad. Directly wiring the fan to a 12 volt power source will tell you if the motor is toast. If it won't work when directly wired to a power source, look for another motor.
Can i run a 240 volt water heater on 120 volt?
No. A water heater requires a 240 volt connection and cannot be re-wired to run on 120 volts. There isn't enough amperage in 120 volts to power the heating rods that are inside.
How do you know if you have a series circuit or parallel?
A series circuit will be wired from the power source at the positive input of the first device, the second device will receive power from the output of the first device and then go back to ground. A parallel circuit is wired so that both devices receive power from the power source directly to the positive input and both are wired directly to ground.
Can a car amplifier be wired in a house to power subs?
yes but u would have to hook the amp up to a power source and ground it
where can i buy a reliable water heater?
You can find water heaters at any home improvement store. It's best to make sure your house is properly wired before you spend time and money investing in a new water heater.
How is the power wired in a 3-way switch setup where the power source is located at the light fixture?
In a 3-way switch setup with the power source at the light fixture, the power is wired from the circuit breaker to the light fixture, then to the first switch, and finally to the second switch. This creates a loop that allows the switches to control the light fixture from different locations.
What is wrong with a car radio when it will not cut off when the car is off?
If it has recently been wired in it has probibly not been wired in correctly. There are normally two power points for a car radio, one constant and another that works only when the ignition is on. By the sounds of it, it is wired into the constant power source, hence not switching off with the ignition.
How is a car headlight wired?
Car headlights can be used to illuminate work areas, crawl spaces, and other areas where AC power is not available. In order to use headlights, they must be wired to a car battery or some other source of DC power.
Can a 100 amp sub main handle a 27 KW Electric water heater wired to 3 40 amp breakers?
You need to say what voltage the heater is running on (it's different in different countries).
How are loads or power -consuming devices wired?
Loads or power consuming devices are usually wired?
When Does it matter if a gas heater fan blower is wired reverse polarity?
It matters if the gas heater fan blower is wired with reverse polarity because it can cause the motor to run in the wrong direction, resulting in inefficient air circulation or overheating. This can also potentially lead to damage to the motor or the electrical components of the heater. It is important to have the blower wired correctly to ensure the proper functioning and safety of the gas heater.
How are loads or power-consuming devices usually wired?
Loads or power-consuming devices are usually wired
