0
Add your answer:
Earn +20 pts
What kind of wire do you use for 120 volts and what amp breaker do you use?
#12/2wground & a 20 amp breaker should be enough for lights,receptales.
How many 50 watt lights on a 15 amp circuit?
50 watt equals less than 1/2 amp current flow at 120 volts so you can have 30 light on a 15amp breaker or 40 on a twenty amp breaker.
Can you use 40 amp breaker for your lights and plug ins?
If you are referring to house wiring then the answer is no. A breaker protects the wire size that is connected to the breaker. In home wiring most homes are wired with a #14 wire which is rated at 15 amps. That is why the wire is protected by a 15 amp breaker. The correct wire size to connect to a 40 amp breaker is a #8. This size wire is too large to connect to receptacles an light fixture terminals.
How many electrical outlet can be install to a 30amps breaker?
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
Is a double throw 15amp breaker the same as a 30 amp breaker amp?
You have a double pole breaker for 240Volt supply. The maximum current is 15 amp.
What kind of wire do you use for 120 volts and what amp breaker do you use?
#12/2wground & a 20 amp breaker should be enough for lights,receptales.
Can six recessed lights of 50 watts be on a 15 amp breaker?
Should be fine if that is all that is on the breaker.
How many 50 watt lights on a 15 amp circuit?
50 watt equals less than 1/2 amp current flow at 120 volts so you can have 30 light on a 15amp breaker or 40 on a twenty amp breaker.
How many canned lights can go on one breaker?
The number of can lights that can go on one breaker will depend on the wattage of each light and the maximum load capacity of the breaker. It's important to calculate the total wattage of all the lights and ensure it does not exceed the amp rating of the breaker to avoid overloading it. Consult with an electrician to determine the appropriate number of can lights that can safely go on one breaker.
How many lights can run off a 15 amp breaker?
Generally, a 15 amp breaker can safely handle around 1440 watts of power. The number of lights that can run off this breaker depends on the wattage of each light. As a guideline, if each light consumes around 60-75 watts, you can safely run about 16-24 lights on a 15 amp breaker.
Can a 15 amp breaker hold 300 watts at 120 volts?
Yes, it can.
New shop 20 amp circuit 32 amp fixture how many fixtures can be put on circuit?
A 32 amp fixture can not be fed from a 20 amp breaker as the breaker will trip every time.
Duplex receptacle circuit given 15 amp breaker 225 amp load?
A 15 amp breaker is not sufficient for a 225 amp load. You would need a breaker that matches the load current, such as a 225 amp breaker. Using a 15 amp breaker for a 225 amp load would cause the breaker to trip immediately due to overcurrent.
How do you turn a 30 amp circuit into a 15 amp cicuit?
Replace the 30 Amp Breaker with a 15 Amp breaker.
How many volts can you draw off of a 15amp breaker?
On a 15 amp breaker, you can draw up to 120 volts in a standard residential circuit. The voltage remains constant at 120 volts, but the amperage capacity is what is limited by the 15 amp breaker.
Can you use 40 amp breaker for your lights and plug ins?
If you are referring to house wiring then the answer is no. A breaker protects the wire size that is connected to the breaker. In home wiring most homes are wired with a #14 wire which is rated at 15 amps. That is why the wire is protected by a 15 amp breaker. The correct wire size to connect to a 40 amp breaker is a #8. This size wire is too large to connect to receptacles an light fixture terminals.
How many electrical outlet can be install to a 30amps breaker?
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
