0
The ampacity of number 8 aluminum wire can vary based on factors like insulation type and ambient temperature, but it typically ranges from about 30 to 40 amps for general use. For a 200-foot run, voltage drop should also be considered, as longer distances can reduce efficiency. It's advisable to use voltage drop calculations to ensure the wire can handle the intended current without excessive loss. Always consult local electrical codes and standards for specific applications.
What else can I help you with?
What size aluminum wire needed for 30 amp at 240 volt for 500 feet underground?
A 1/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 30 amps for 500 feet on a 240 volt system.
What size aluminum wire for 100 amps undergroundservice 60 feet from meter?
A 3/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 150 amps for 150 feet on a 240 volt system. This size will allow the conductor to be loaded to 120 amps. 150 x 80% = 120 Conductors are only allowed to be loaded to 80% or their rated capacity. If you need the full 150 amps then you would need to use a wire with a rating of 190 amps. 190 x 80% = 152 amps A 4/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 190 amps for 150 feet on a 240 volt system.
What gauge wire for aluminum 240 volts 20 amp 200ft?
A #6 aluminum conductor will limit the voltage drop to 3% or less when supplying 20 amps for 200 feet on a 240 volt system.
What size aluminum wire to feed 125 Amps 220 volt a distance of 175' and what size ground?
A 3/0 aluminum conductor will limit the voltage drop to3% or less when supplying 125 amps for 175 feet on a 220 volt system. If the 125 amp load is a sub distribution panel that is not going to be fully loaded to 125 amps then using the exact connected load, which might be smaller than 125 amps will effect the wire sizing. The grounding conductor for that size distribution panel is #6 bare copper.
What size aluminum wire needed for 60 amp at 240 volt for 330 feet underground?
A 1/0 AWG aluminium conductor will limit the voltage drop to 3% or less when supplying 60 amps for 330 feet on a 240 volt system. The cable will be rated as ACWU 90. ACWU 90 cables are primarily intended for exposed and concealed wiring in dry or wet locations and where exposed to the weather. For use in ventilated, non-ventilated, and ladder type cable trays in wet and dry locations; direct earth burial; service entrance above or below ground.
What size aluminum wire needed for 30 amp at 240 volt for 500 feet underground?
A 1/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 30 amps for 500 feet on a 240 volt system.
What size aluminum wire for 100 amps undergroundservice 60 feet from meter?
A 3/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 150 amps for 150 feet on a 240 volt system. This size will allow the conductor to be loaded to 120 amps. 150 x 80% = 120 Conductors are only allowed to be loaded to 80% or their rated capacity. If you need the full 150 amps then you would need to use a wire with a rating of 190 amps. 190 x 80% = 152 amps A 4/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 190 amps for 150 feet on a 240 volt system.
What gauge wire for aluminum 240 volts 20 amp 200ft?
A #6 aluminum conductor will limit the voltage drop to 3% or less when supplying 20 amps for 200 feet on a 240 volt system.
What size aluminum wire to feed 125 Amps 220 volt a distance of 175' and what size ground?
A 3/0 aluminum conductor will limit the voltage drop to3% or less when supplying 125 amps for 175 feet on a 220 volt system. If the 125 amp load is a sub distribution panel that is not going to be fully loaded to 125 amps then using the exact connected load, which might be smaller than 125 amps will effect the wire sizing. The grounding conductor for that size distribution panel is #6 bare copper.
What size aluminum wire needed for 60 amp at 240 volt for 330 feet underground?
A 1/0 AWG aluminium conductor will limit the voltage drop to 3% or less when supplying 60 amps for 330 feet on a 240 volt system. The cable will be rated as ACWU 90. ACWU 90 cables are primarily intended for exposed and concealed wiring in dry or wet locations and where exposed to the weather. For use in ventilated, non-ventilated, and ladder type cable trays in wet and dry locations; direct earth burial; service entrance above or below ground.
How many amps will 2-2-2-4 carry at 180 feet?
150 amps
How do you make 3.2808399 through a feet stick?
Without a given unit, you can not make that number through a feet stick. You need to include a unit in order to indicate the number on the stick.
What size wire needed for 100 amp service 700 feet away?
A 400 MCM copper conductor will limit the voltage drop to 3% or less when supplying 100 amps for 700 feet on a 240 volt system. This size will allow the conductor to be loaded to 80 amps. 100 x 80% = 80 amps. Conductors are only allowed to be loaded to 80% or their rated capacity. If you need the full 100 amps then you would need to use a wire with a rating of 125 amps. 125 x 80% = 100 amps. A 600 MCM copper conductor will limit the voltage drop to 3% or less when supplying 125 amps for 700 feet on a 240 volt system.
What size wire to carry 20 amps 100 ft?
To carry 20 amps over a distance of 100 feet, you typically need to use at least 10-gauge wire for copper or 8-gauge wire for aluminum. This accounts for voltage drop and ensures safe operation. Always consider local codes and regulations, and consult a professional electrician if unsure.
How many amps will 10-2 wire carry at 40 feett?
30 amps is how much a 10-2 wire will carry at 110 feet. 10 gauge wire is only good for thirty amps per the national electrical code. Using 80% of the breakers usage you will actually be getting only 24 amps.
Is body heat lost through feet?
Yes, body heat can be lost through the feet due to the large number of blood vessels in the feet that can release heat into the environment. Wearing socks and appropriate footwear can help to minimize heat loss through the feet.
Need to run 30 amps about 100 feet what copper wire?
This is a voltage drop question. A voltage at 30 amps needs to be stated to answer the question.
