Wiki User
∙ 10y agoThere is no switch on an outlet. You can mount an outlet with the ground up or down. Most electricians I know mount the ground down as I do.
Wiki User
∙ 10y agoMany outlets have small tabs between the terminal screws that can be broken out with a needle nose pliers. You can completely separate the continuity of the top outlet from the bottom outlet by breaking both these tabs and wiring each outlet as a completely separate circuit. The ground plug is the only line that cannot be separated this way, and will remain common for both outlets. Alternatively you can break a tab only on one side and have the outlet share either the neutral or hot line. For a outlet set up to have constant power on the bottom break the tab on the neutral side, wire your hot line as normal and the "constant" neutral to the bottom neutral terminal, then run a second neutral from your switch. This would allow for the bottom outlet to be live all the time and the top to be switched on or off.
Most new installations in new homes will have this feature. It is for a "garburator" which is connected to the kitchen sink outlet. There is usually a switch mounted on the wall near the sink for switching it on and off. The switch is usually mounted in a two gang junction box. The other device in the junction box is an electrical receptacle.
Yes you just have to "steal" power from the switch. Do this by running a pigtail wire from the hot of the switch to the hot wire of the plug. Make sure you do this before the switch or you will end up with your outlet being switched as well.
In this case, flush means even with. For example an electric box could be mounted on the outside of your wall and would be an eyesore. Flush mounting recesses the box inside the wall and provides a flush mount for the outlet cover plate.
You can wire a dimmer into any circuit. The issue is where you do it for a specific outlet. The dimmer would just have to connect to a single outlet and not all outlets on the same circuit. The issue is getting a dimmer that is compatible with the device you are dimming. Some lighting requires special dimmers.
It is mounted at the windshield washer tank outlet (on the bottom of the tank). You need to remove the tank from its engine compartment mounting to gain access.
You can find a Coach bag outlet from the official Coach website. If you browse to the store locator portion of the website, there is a button near the bottom that will allow you to search for Coach factory stores.
Many outlets have small tabs between the terminal screws that can be broken out with a needle nose pliers. You can completely separate the continuity of the top outlet from the bottom outlet by breaking both these tabs and wiring each outlet as a completely separate circuit. The ground plug is the only line that cannot be separated this way, and will remain common for both outlets. Alternatively you can break a tab only on one side and have the outlet share either the neutral or hot line. For a outlet set up to have constant power on the bottom break the tab on the neutral side, wire your hot line as normal and the "constant" neutral to the bottom neutral terminal, then run a second neutral from your switch. This would allow for the bottom outlet to be live all the time and the top to be switched on or off.
"S.S.O." likely stands for "Single Socket Outlet." "13A" indicates that the outlet is rated for a maximum current of 13 amps.
If a nearby outlet sparks when the room light is switched on, immediately turn off the light switch and unplug any devices from the outlet. Do not use the outlet until it has been repaired or replaced by a qualified electrician to prevent the risk of an electrical fire.
That happens when the appliance supplied by the outlet is switched off.
It is not recommended to have an outlet next to a wall-mounted electric heater, as the outlet can be a fire hazard due to prolonged exposure to heat from the heater. It is important to consult local building codes and regulations regarding the placement of electrical outlets near heat sources.
To install a 120V outlet with top plug control from a wall switch, you'll need to replace the existing outlet with a split-wired outlet. Connect the bottom plug to power constantly, and the top plug to be switched by the wall switch. Consult an electrician if you're unsure of the wiring process to ensure safety and compliance with local electrical codes.
It is called a back outlet toilet floor mounted
Yes, you can extend power through the 3-wire switch leg to a new switch for a new light. You would need to connect the hot wire to the common terminal on the existing switch, then extend the hot wire to the new switch, along with the traveler wire. At the new switch, connect the hot wire to the common terminal and the traveler wire to one of the traveler terminals.
No, an outlet box cannot be mounted directly to an electrical panel. Electrical panels have specific requirements for clearance and access, and mounting an outlet box to it would violate those safety guidelines. It is recommended to install outlets separately on the wall near the panel if needed.
Outlet rating should be suitable to the rating of the motor. The type should be preferably IP 55 or higher if mounted outside the sump in dry area.