answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: Should the GFCI light always be on?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Electrical Engineering

Does the neutral wire have a charge in a gfci circuit breaker?

No. Not if the GFCI is wired correctly. The neutral wire should always be cold, or at ground potential.


Do you need gfci on bathroom fan?

No. The only thing required to be gfci protected is a receptacle. I've never understood why light fixtures, fans, and other appliances do not required protection around so much water, but they do not. They should, however, be listed for damp locations.


Can a circuit with a GFCI be shared at the box?

Your question is a bit vague, but let's try a two part answer. If you have a GFCI breaker in an electric panel you should only have one connection at the breaker, but the breaker will protect all devices on the circuit. If you are talking about a GFCI outlet, they are equipped to extend the GFCI protection to other non-GFCI outlets by using the proper "output" connection on the GFCI.


How do you install a GFCI so it is always on to a two way light switch that controls a vent and a light in a bathroom?

Your question sounds simple but it isn't. There are two ways of wiring a light to a switch. One is to bring the hot and neutral wire to the switch box and from there run wires from the switch to the light. If this is the case you can install a GFCI on the circuit. The other way is to bring the hot and neutral wire to the light and from there run two wires to the switch and switch the light that way. In this case you cannot install a GFCI to in the switch box. <<>> The way you want the circuit to work has to be laid out as follows. Method one, the circuit that now controls the bathroom devices can be changed to a GFCI breaker. This is probably the quickest and cheapest, unless the job is new construction. Method two, if new construction use this method, as tearing walls open to get to the wiring will become costly. Where a supply circuit comes from the service distribution panel the first device on that circuit has to be a GFCI receptacle. This device has secondary terminals on it, that if connected every device downstream from it will also be protected. So if you supply the two way light switch that controls the vent fan and a bathroom light from the secondary terminals from the GFCI receptacle they will be protected.


How do you install multiple GFCI receptacles?

A GFCI receptacle can extend its protection to regular receptacles connected to the output side of the GFCI. Each actual GFCI receptacle should be directly connected to a breaker in electric panel.

Related questions

Does the neutral wire have a charge in a gfci circuit breaker?

No. Not if the GFCI is wired correctly. The neutral wire should always be cold, or at ground potential.


The gfci indicator light is on but appliances connected to the gfci outlet are still powered what is causing this?

It's possible that there is a miswiring or a faulty GFCI outlet. You should have a qualified electrician check and repair the outlet to ensure it is functioning correctly and providing the proper level of protection.


How can the light on my GFCI outlet be on when there is no power coming to the outlet?

GFCI outlets have internal circuitry that can power the indicator light even when there is no power flowing to the outlet itself. This function allows you to easily identify if the outlet has tripped or if there is a fault in the circuit.


What is a indicator light on a gfci switch for?

An indicator light on a GFCI switch is used to visually indicate whether the switch is receiving power and whether the GFCI protection is functioning properly. This helps users quickly identify any issues with the GFCI switch without having to test it manually.


What size amp circuit breaker should be used for a pool light?

The pool light is usually on a 15 amp circuit. The breaker feeding this circuit must have a GFCI rating.


Is it safe to use a GFCI outlet that works if the green light stopped working?

If the GFCI outlet is still functioning properly and providing protection, it is generally safe to use even if the green light is not working. However, it is a good idea to periodically check the outlet to ensure it is functioning correctly. If you are unsure, it may be best to consult a professional electrician for further evaluation.


How often should GFCI be tested?

GFCI outlets should be tested monthly to ensure they are working properly. This can be done by pressing the "Test" and then "Reset" buttons on the outlet. If the GFCI does not trip when tested, it may need to be replaced.


Can a GFCI receptacle be fed from a switch?

If this question is asking if, by using a GFCI, you can protect some equipment controlled by an existing switch, the answer is Yes. My first guess would be that you probably don't need to. A switch that is controlling lighting in an area with a GFCI, such as a bathroom, should - if it was installed correctly - already be controlling a proper lighting fixture. By this I mean if the fixture is above the shower it will be of a type that is safety-listed 'for use in wet locations'. That type of light fixture does not need to be protected by a GFCI since it is designed for use around water. How to feed a switch from a GFCI: Without GFCI protecting the switch: Connect a hot (usually black) wire from the "LINE" side of the GFCI (which will be marked) to one brass screw of the switch. (Assumption is single pole switch.) Connect another hot wire from the other brass screw of the switch to the light fixture or load's hot wire. Connect a neutral (white or gray) from the LINE side of the GFCI all the way to the load neutral without stopping anywhere. Connect all grounds. To GFCI protect the switch: The procedure is the same except you will use the hot and neutral from the "LOAD" side of the GFCI. This will cause the GFCI to interrupt power should a ground fault occur on the switched load. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


Do you need gfci on bathroom fan?

No. The only thing required to be gfci protected is a receptacle. I've never understood why light fixtures, fans, and other appliances do not required protection around so much water, but they do not. They should, however, be listed for damp locations.


Can a circuit with a GFCI be shared at the box?

Your question is a bit vague, but let's try a two part answer. If you have a GFCI breaker in an electric panel you should only have one connection at the breaker, but the breaker will protect all devices on the circuit. If you are talking about a GFCI outlet, they are equipped to extend the GFCI protection to other non-GFCI outlets by using the proper "output" connection on the GFCI.


How do you test and reset a GFCI receptacle?

GFCI (Ground Fault Circuit Interruptor) A GFCI receptacle can be tested with the built-in test button, which will cause a small ground fault, tripping a properly working device. GFCI receptacles should be tested monthly. GFCI receptacles can also be tested with a plug-in type GFCI tester. This tester has a GFCI trip button on it which accomplishes the same thing as the built-in test button. Your local inspector will usually test with this method. If your receptacle is tripped, it should reset by pressing in the reset button. If it doesn't, the device is wired incorrectly, has a faulty load plugged into it, or is simply in need of replacement. ---- IF YOU'RE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator to insure the circuit is, in fact, de-energized.


How do you install a GFCI so it is always on to a two way light switch that controls a vent and a light in a bathroom?

Your question sounds simple but it isn't. There are two ways of wiring a light to a switch. One is to bring the hot and neutral wire to the switch box and from there run wires from the switch to the light. If this is the case you can install a GFCI on the circuit. The other way is to bring the hot and neutral wire to the light and from there run two wires to the switch and switch the light that way. In this case you cannot install a GFCI to in the switch box. <<>> The way you want the circuit to work has to be laid out as follows. Method one, the circuit that now controls the bathroom devices can be changed to a GFCI breaker. This is probably the quickest and cheapest, unless the job is new construction. Method two, if new construction use this method, as tearing walls open to get to the wiring will become costly. Where a supply circuit comes from the service distribution panel the first device on that circuit has to be a GFCI receptacle. This device has secondary terminals on it, that if connected every device downstream from it will also be protected. So if you supply the two way light switch that controls the vent fan and a bathroom light from the secondary terminals from the GFCI receptacle they will be protected.