0
Add your answer:
Earn +20 pts
What is equivalent wattage when different wattage resistors are connected in parallel?
In order to determine this, it will be necessary to find which resistor 'maxes out' at the lowest voltage. This can be found using the equation Vi=sqrt (Pi*Ri) for each resistor, where Pi is the power rating of resistor i and Ri is the value of resistor i. Once this is found, the power dissipation of each other resistor can be found using the equation Pi=(Vl^2)/Ri, where Vl is the voltage that maxes out the resistor which maxes out at the lowest voltage, and Ri is the resistance of each resistor. The equivalent power rating would then be the sum of the power dissipated across each resistor.
How do you use an amplifier?
Amplifiers comes in IC packages diagram is triangle with +/- input by adding a resistor r1 in series to the - input the gain can be found by adding a resistor from output to the - input The + terminal must be satisfied with the proper resistor
Why resistor should disconnected from the circuit when measured the value of resistor?
if not disconnected you will measure the resistance of the circuit in parallel with the resistor.
What is the relation between the size of the resistor and its value?
There is no relation between the resistor's ohms value and its size. The power of the resistor can be seen by its size. If the power is too small, the resistor can be destroyed.
A 5 ohm resistor a 10 ohm resistor and a 15 ohm resistor are connected in series to a 120 volt power source. What is the amount of current flowing between the 5 ohm resistor and the 10 ohm resistor?
The current would be about 20 volts.
Where is blower motor resistor on an Infiniti i30?
The blower motor resistor, for your infinity automobile, can be found in the engine compartment on the firewall. The resistor will be on the passenger side of the firewall.
What is equivalent wattage when different wattage resistors are connected in parallel?
In order to determine this, it will be necessary to find which resistor 'maxes out' at the lowest voltage. This can be found using the equation Vi=sqrt (Pi*Ri) for each resistor, where Pi is the power rating of resistor i and Ri is the value of resistor i. Once this is found, the power dissipation of each other resistor can be found using the equation Pi=(Vl^2)/Ri, where Vl is the voltage that maxes out the resistor which maxes out at the lowest voltage, and Ri is the resistance of each resistor. The equivalent power rating would then be the sum of the power dissipated across each resistor.
Where is blower motor resistor on 1992 Carina?
The blower resistor is located behind the dashboard. It is found behind the heater near the center of the vehicle.
How calculated the value of resistor that is to be used in particular circuit?
To read the value of a resistor: Resistors are color coded, you can use the chart found below And how accurate the values of resistors are is their tolerance, also found in the chart
How do you find a blower motor resistor in a 1988 ford van?
The blower resistor is usually found attached to the A/C-heater box under the hood.
How do you use an amplifier?
Amplifiers comes in IC packages diagram is triangle with +/- input by adding a resistor r1 in series to the - input the gain can be found by adding a resistor from output to the - input The + terminal must be satisfied with the proper resistor
Where is the heater motor resistor in a 1995 dodge Dakota?
Diagram for location of blower motor resistor can be found herehttp://autorepair.about.com/library/images/bl441a-lib.htm
Where is the blower resistor located on a 1992 BMW 325i?
The blower resistor on the 1992 BMW 325i is located under the center console. It is found on the driver's side.
Where is the blower motor resistor of a Mazda mpv 2002?
Generally the blower motor resistor is found close to the blower motor. It relies on the blower motor to keep it cool.
Blower motor resistor location for a 99 Dakota?
For a 1999 Dodge Dakota the Blower resistor is located in the firewall under the Cowl panel (Plastic panel under wipers). The wiper arms must be removed to remove the cowl panel. The resistor is located on the passengers side inside an access hole. My blower only works on High. I just removed my resistor and found that the connector was not plugged into the resistor. I finally found the plug under the dash. Does anyone have any idea on how to plug the connector back into the resistor without removing the complete instrument panel??
Where is the heater resistor on a 1990 freightliner truck?
they are usually found close to the blower motor.
Where is the heater fan resistor on Renault master found?
where is renault master fan resister
