answersLogoWhite

0

What else can I help you with?

Continue Learning about Electrical Engineering

How do you connect an ON-OFF switch to control the light?

To control a light with a switch, the switch has to be connected in series with the light fixture.


To mount two switches and a pilot light in a single gang standard device box you would use?

You would need to purchase a duplex switch. As for the pilot light look for a duplex switch that has a neon pilot light that is incorporated into the handle of the switch. When the switch is turned on the switch's handle will illuminate.


What is the difference between single pole switch and a three way?

A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.


Light not going when switching off?

if light is not going off, bad switch or short in wiring to light!!


How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?

If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.

Related Questions

Tell why both front light of yamaha fazer does'nt swiched on at the same time or its a manufacturing defect in my bike?

no. its not manufacturing defect on at one time in one light switch on one light is high beem & one light is low beem


Manufacturing process for kettle?

manufacturing process of kettle


Definition of core in manufacturing process?

the process of manufacturing


How is the phased manufacturing process used in industries?

phased manufacturing process


How do you fix the hazard light switch on a 97 Crown Victoria?

Remove the wiring harness from the back of your 1997 Ford Crown Victoria hazard lights switch. Remove the hazard light switch retaining screws. Reverse the process to install your new hazard light switch.


What are the three important phases in the manufacturing process?

3 phases in manufacturing process


Where can the manufacturing process be learned about?

There are a number of firms that publish their manufacturing process online. You can find out about the manufacturing process through education websites as well, such as ALISON.


How can I install a switch to control the light in my room?

To install a switch to control the light in your room, you will need to turn off the power to the light fixture, remove the existing switch, connect the new switch following the manufacturer's instructions, and then test the switch to ensure it is working properly. It is recommended to consult a professional electrician if you are unsure about the installation process.


How is a light bulb made and what are the steps involved in its manufacturing process?

A light bulb is made by first creating a glass bulb, then adding a filament and gases inside. The manufacturing process involves shaping the glass, adding the filament, sealing the bulb, and filling it with gases. Finally, the bulb is tested and packaged for sale.


What is the name of the process by which they are created?

The manufacturing process.


What is virtual manufacturing?

Virtual manufacturing is the process of designing a product or creating a manufacturing process, using special 3-D software. Virtual manufacturing allows companies to work out any glitches in product design, and streamline the manufacturing process before it actually begins.


Why is the dimmer switch hot?

The dimmer switch can become hot because it regulates the flow of electricity to control the brightness of the light. This process can generate heat as a byproduct.