Wiki User
∙ 15y agoGo to this site http://www.generatorjoe.net/html/nemaplugs.html and tell me what configurations you have and I might be able to help you.
Wiki User
∙ 15y agoAnswer for USA, Canada and other countries running a 60 Hz supply service.Stop! What...? Don't try to do that...!Don't make a cable with the intention of plugging a generator into an outlet in your house, it is incredibly dangerous!Power from your generator will back-feed into the power lines, posing a severe unexpected shock hazard to any line-workers who may be fixing the lines - the very same reason you are wanting to use your generator!Plug your appliances directly into the outlets on your generator. If you want to power the outlets in your house from the generator you must do it right and install a proper 'generator transfer switch' at the main incoming breaker panel which is situated where the main electricity service cable comes into your house.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
A NEMA 5-20 plug is a standard 3 prong plug. It wires the same as a NEMA 5-15 plug (Ground wire to the "D" contact, Hot to vertical terminal and neutral to the horizontal terminal (with the Ground terminal either at the top or bottom)).A 5-20P plug has the neutral blade rotated 90°. The 5-20R receptacle usually has a T-shaped neutral hole, to accept both 5-15P and 5-20P plugs.
start generator, plug in variable speed drill, set drill to forward, squeeze trigger, quickly spin drill in reverse by hand. be sure generator main breaker is on.
On a 240 volt outlet, such as a dryer outlet: G is Ground, W is Neutral, X and Y are the two Hot legs.
If you are refering to a wall receptacle, the one on the right is the hot side. The left side is the neutral and it's slot is larger that the hot one. The U shaped on the bottom is for the ground pin of the plug.
Check Lowes and Home Depot they normally carry the adaptors
You will need a step-down transformer to convert the generator's higher voltage output to the standard 110V house current. Make sure the transformer is rated for the appropriate wattage to power your devices safely. It's recommended to consult an electrician to ensure proper setup and safety.
Yes, you can plug a power strip into a generator to run multiple items, but it's important to ensure that the overall power draw of the devices plugged into the power strip does not exceed the generator's capacity. Be mindful of the total wattage of all items connected to the power strip to avoid overloading the generator.
No you can not you will need to replace the plug with a 4 prong the same as the style of your oven and change your breaker to the correct Amp for your style of 4 prong plug
Answer for USA, Canada and other countries running a 60 Hz supply service.Stop! What...? Don't try to do that...!Don't make a cable with the intention of plugging a generator into an outlet in your house, it is incredibly dangerous!Power from your generator will back-feed into the power lines, posing a severe unexpected shock hazard to any line-workers who may be fixing the lines - the very same reason you are wanting to use your generator!Plug your appliances directly into the outlets on your generator. If you want to power the outlets in your house from the generator you must do it right and install a proper 'generator transfer switch' at the main incoming breaker panel which is situated where the main electricity service cable comes into your house.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Ground wire
It could be a loudspeaker polarised plug.
A 2 prong plug won't fit in a 3 prong outlet because the third prong, known as the ground prong, creates a different configuration that prevents the two-prong plug from being inserted. The ground prong is wider than the other two prongs, so a 2 prong plug lacks the necessary space for the third prong to be accommodated.
Need to know the amperage rating of the plug or the NEMA configuration of the plug and receptacle
Connect the ground wire to the neutral prong on the generator. This setup will allow you to safely power your dryer using a three-wire cable with a four-prong style plug. Make sure the installation adheres to safety guidelines and local electrical codes.
US dryers commonly use a 3-prong or 4-prong plug. The 3-prong plug has two flat blades (hot) and a L-shaped prong (neutral), while the 4-prong plug has two flat blades (hot), a round prong (neutral), and a half-round prong (ground). It's important to match the plug with the corresponding outlet for safety and proper functionality.
No, the wide prong is neutral it is the white wire. The narrow prong is hot it is the black wire. The round prong (in a 3 wire plug) is safety ground it is the green wire.