0
metering system assembly consists of the following sub-skid:
1. Metering skid, consist of ultrasonic flow meter, pressure transmitter, temperature transmitter, pressure gauge, temperature gauge etc.
2. Analyzer shelter, consist of gas chromatograph, dew point analyzer, and moisture analyzer.
3. Gas metering panel, consist of flow computer and station computer (usually gas metering panel are located inside the control room).
Add your answer:
Earn +20 pts
What is use of metering core in transformer bushing?
It is the current transformer core meant for metering.
What metering device is the most efficient for heat pumps?
Thermostatic Expansion Valve (TXV, TEV). Any high efficient system requires one.
What is the accuracy of 3 phase 4 wire system to 3 phase 3 wire metering system?
It makes no difference as to what system is being monitored. The meter itself has to be accurate because it comes under the government's weights and measures department. Meters in the field are checked if the consumer thinks there is a problem with their billing. Before a meter is put into service they are all checked for accuracy by an independent agency.
How does HVAC work?
HVAC works with four major parts; The compressor, which is the heart of the system. An Evaporator, which abosorbs heat the form the structure. Third the condenser, which releases heat from inside and puts it in a place where it makes not difference, usely outside. Lastly the Metering device, which seperates the high and low side of the system. We will start at the compressor which pushes the refrigerant to the condenser at high pressure. In that process the refrigerant heated up do to the compression, the reason for going to the condenser is so the heat from compression and heat from in the house can be released. After the heat has been released and refrigerant is condensed it moves to the metering device which depending on how old your system is can be multiple devices we will just say it is a very small hole so normal people will understand. As the refrigerant is leaving the metering device it is now turning into liquid as well as going down in pressure. when it reaches the evaporater this liquid boils off back into vapor becaus in the evaporater it absorbs heat from the house. now it travels back to the compressor now fully vapor to be compressed and sent around again.
What is the impact of reversing the polarity of a CT in a 3phase and 4wire metering arrengement?
The net measured power would appear to be negative, or reversed.
What is the Meaning of fiscal meter?
Fiscal metering is defined by the Metering Regulations as "Metering related to the purchase and sale and calculation of taxes" It is a measurement of product (usually Crude Oil) flowing through a pipeline or other such system and is used to determine payment or other charges due. The metering system is regularly checked for correct reading by comparison to International standards.
Where the refrigeration changes in a refrigeration system?
at the metering device before the evaporator
What is the refrigerant entering the metering or expansion device of a refrigeration system?
superheated vapor
What causes most vehicle skids?
ice What causes most skids?
Who older skids or mudflap?
I would say Skids is older then Mudflap.
When was Joy - Skids album - created?
Joy - Skids album - was created in 1981.
How many metering modes are available on a Nikon D70 camera?
One can check in the Nikon D70 manual.There are three metering mode available on a Nikon D70 camera.Spot metering mode,Matrix metering mode and Center-weighted metering modes.
What is the SIC Code for Wood Pallets and Skids?
SIC 2448 applies to WOOD PALLETS AND SKIDS.
What is Net Metering?
The grid connected rooftop system can work on net metering basis wherein the beneficiary pays to the utility on net meter reading basis only. Alternatively two meters can also be installed to major the export and import of power separately. The mechanism based on gross metering at mutually agreed tariff can also be adopted.
What is a brake combination valve?
A valve in the brake system which houses portioning valve metering and pressure differentional valve
What Transformers characters are considered to be Skids?
The Transformer characters that are considered to be Skids were from the Transformers Universe cartoon. They were part of the Autobots Transformers. There was also a character names Skids in the movie Tranformers:revenge of the Fallen.
Are mudflap and skids pimps?
......no
