0
Add your answer:
Earn +20 pts
What fastens the gauge line to the end fittings of a gauges line?
Ghji
Does a line have a beginning but no end?
No. A geometric line has no beginning or end. A ray has a beginning, but no end. A line segment has both a beginning and an end.
Why does a line have two arrows at the end of it?
It sigals that the line is not just a line segment but that this line does NOT end.... ever.
What is a end stopped line?
A line of poetry in which the meter and the meaning conclude with the end of the line.
What is and end stopped line?
An end-stopped line is a line of poetry which has a natural pause at the end, usually because of punctuation.
What fastens the gauge line to the end fittings of a gauges line?
Ghji
1993 Eagle Summit How do you replace a break line on a 1993 Eagle Summit?
unscrew the fittings at each end of the line
Can a hole in the break line be fix without replacing the line?
Yes. BUT, only if the rest of the line is in good shape. Cut the line with a pipe cutter, buy the necessary fittings, put the fittings on each end of the line, and flare the line with your double flare kit. Remember, it has to be double flared to hold.
How many grease fittings 2008 Chevy Silverado?
2 Grease Fittings. One on each Tie Rod End.
If I have 150ft of 10 gauge wire with 60 amp service how many amps and watts do I have available at the end of the line?
10 gauge wire will only run up to 30 amps
How do you replace a fuel filter on a 1987 Chevy Corsica?
(Licenced Technician)--Most of these older Corsicas (regardless of engine size) have the fuel filter mounted in a bracket that's bolted to the body. Look under the rear of the car - it's about 12" above the fuel tank. These older Corsicas have two threaded fuel line fittings on the filter. You have to unscrew the threaded fittings from each end of the filter, then install the new filter and tighten the fittings tightly enough so they don't leak, but not so tight as to damage the fittings. You will likely need a selection of open end wrenches and maybe a ratchet with a socket if you need to remove the filter bracket. If you live somewhere that a lot of salt is put on the roads in the winter, lots of penetrating oil may be needed. On a 20-year old car, the best rule is; if the line fittings don't want to loosen off, DON'T FORCE THEM - the line could kink or break, or at the very least, the fittings could round off. .
How do you install orifice tube in a 2003 2500 Chevy truck?
The ones I have worked on, you replace the line that goes from the condenser towards the firewall. The orifice tube is captured in the firewall end of the line, between the high side & low side valve fittings.
How do you change a brake line on the brake booster?
The brake lines are not attached to the booster. They are attached to the master cylinder. To remove them, use an opened end wrench on the fittings located where the lines meet the master cylinder and slowly turn counter clockwise. BE CAREFUL NOT TO STRIP THE FITTINGS THEY ARE MADE OF BRASS AND ARE VERY SOFT!
How can you tell when a home pressure regulator has gone bad?
An easy way to check your water pressure is to install a gauge using an ice making line kit tapped into an easy spot like under the sink. Just put the gauge on the end of the ice maker line.
How do you remove hydraulic clutch line from the transmission on 1996 Chevrolet 2500?
My 94 has a spring pin that pushes out of the connectors on either end. Since the steel pins are located in plastic fittings, they come out easily.
Are aqua pex fittings and super pex fittings the same?
I had the same question today. The answer is no. Aquapex had an aluminum casing and so the sharkbite fittings will not work on Aquapex. Now searching for aquapex fittings. Yes, the Sharkbite fittings work on Aquapex. I plumbed my cottage 3 years ago with Aquapex and fittings. Recently, I have had difficulty finding Aquapex fittings. My new work is done with Sharkbite fittings. These fit easily onto the Aquapex pipe. I have used tee joints and inline valves. As with Aquapex fittings, yo have to ensure that the pipe end is round first. Use the Aquapex reaming tool. ---------- The link below can give you a better understanding of PEX fittings types.
How many grease fittings does a Jimmy Have?
Depending on year, it came with 11 or 2 or 4 or 8 or 0. Repairs to front end and/or driveshafts may have added additional grease fittings.
