0
What else can I help you with?
Is the diameter of a circle bigger or smaller then the radius?
The diameter is twice as long as the radius. d = 2r The diameter is basically a line through the center of a circle while a radius is from the center to the circumference of a circle.
What is a dimension line?
Lines that define the parameters of a dimension.Dimension lines are thin lines terminating in arrowheads. Place dimension lines no closer than 3/8" from the object outline. Parallel dimension lines should be a minimum of 1/4" apart. You may place parallel dimension lines more than 1/4" apart so long as the spacing between dimension lines is uniform throughout the drawing. Dimension lines are generally broken in the center of the line to provide a space for the dimension figure. Dimension figures for parallel dimension lines are staggered. In some structural or architectural drawings, you may find dimension figures placed above the dimension line.
If the diameter of a circle is 12 cm long how long is the radius?
The radius would be 6 cm because the diameter is 2 times bigger than the radius.
How long is the radius of a 5 square mile circle?
The radius is 1.261 miles.
If the circumference of a circle is 94.2ydhow long is the radius?
radius = 94.2/(2*pi) = 14.99239564 or about 15 yards
How do you get the center of elbow?
Formula for calculating center to end distance of such elbows is as follows: For 90° Long Radius elbows, center to end dimension given in dimension tables of ASME B16.9 is same as radius of elbow. This is because Tan (90/2) i.e. Tan 45 is 1. Normally custom elbow angles from 45 degree to 90 are cut from 90 degree standard elbow. If that's what you were asking about...
Is the diameter of a circle bigger or smaller then the radius?
The diameter is twice as long as the radius. d = 2r The diameter is basically a line through the center of a circle while a radius is from the center to the circumference of a circle.
What is the standard fitting allowance for long radius elbow?
3 Litres
What is the difference between long radius and short radius elbow?
In the area of industrial pipe fittings: Long radius 90 deg elbow has a take off dimension of one and one half times the nominal diameter of the pipe. Ex-4 inch pipe has an actual diameter of 4.5, for the elbow the take off dimension would be 4"*1.5=6". The short radius elbow take off dimension is the same as the nominal size, 4". To add to the point, a short radius elbow can be used typically where space is a constraint. Hence fluid flow is also restricted in this case unlike in case using of Long Elbow.
What is the scientific name of radius?
The scientific name of radius is "radius." Radius is one of the two long bones in the forearm, located on the lateral side of the arm when in the standard anatomical position.
A chord of a circle is 9 inches long and its midpoint is 6inches from the center of the circle What is the radius of the circle?
Half of the chord, the distance of the midpoint from the center, and a radius, form a right triangle, with the radius as its hypotenuse. (4.5)2 + (6)2 = (radius)2 (20.25) + (36) = 56.25 = R2 Radius = 7.5 inches
How do you calculate the center of a 90 degree pipe elbow?
If your elbow is a short radius it is 1 times your nominal pipe diameter. If it is a long radius it is 1 1/2 times your nominal pipe diameter.show me the exact pattern of long radius
If A chord twenty four inches long is five inches from the center of a circle what is the radius?
nbvhfvnkjfsdbvyhfndjvnbfyuv r = 4
How is the diameter related to the radius of a circle?
The radius of a circle is a line that starts at the center of the circle and ends somewhere along the perimeter of the circle. The diameter is a line that starts at the perimeter of a circle, goes through the center of the circle, and ends at the opposite perimeter of the circle. This a diameter is twice as long as a radius and can be thought or as consisting of two radii.
What is the formula for finding end to center dimensions on a long radius butt weld elbow?
1/2 tan(dia)1.5
How long is the diagonal dimension of a rectangle with the dimension of 100 by 120?
156.2 units.
How long is a standard bowling alley?
A bowling lane is 60 feet long from the foul line to the center of the headpin. Each pin is 12 inches apart center to center. And the approach (the part you walk on) is 15 feet long.
