0
Angular Misalignment:
Front Foot = (TIR x B)/A
Rear Foot = (TIR x B)/A
Parallel Misalignment:
All Feet = (TIR + Bar Sag)/2
Note:
- Positive values mean adding height (shims); negative mean subtracting height (removing shims).
- TIR = Total indicator runout (the reading on the dial indicator)
- A = The diameter of the circle the indicator makes on the coupling face
- B = Distance between the coupling being measured and the center of the bolt hole on the front foot of the machine being measured.
- C = Distance between the coupling being measured and the center of the bolt hole on the rear foot of the machine being measured.
Add your answer:
Earn +20 pts
What formula is used to determined the contact area of a drum without a rim?
D2x0.785
What is rim elevation of a manhole?
Rim, on a manhole, is the elevation of the top of the cover on the manhole. In a roadway the rim will at be final grade, in grass they can be sumped, flush or stick up.
Why is the radius of the circle half the diameter?
The radius of a circle is the distance from the centre to the rim. The diameter is the distance fron rim to rim passing through the centre point. It therefore follows that the radius is half the diameter
What is the outer edge of a cup?
The out edge of a cup is called the 'Rim'.
What is the shape of a shoe box?
what does a rim of a tea cup looks like
Honda civic back tires are wearing on inside of rim?
needs alignment
Where do you measure the top of rim or bottom of rim to ground?
poopy face
What is alignment of rotor shaft in steam turbine?
steam turbine is multiple shaft euipment, to avoid the viberation of the shaft train runing, the multiple shaft need to be aligned within tolorance. usually, the rim and face run out checked is request.
What is the difference between flange and coupling?
flange is a protruding rim, edge, collar, as on a wheel or a pipe, shaft, used to strengthen an object, hold it place, or attach to another object.while coupling is a device to connect two shaft together at their ends for the purpose of transmitting power.
How does one install a rim lock?
Rim lock sets are one of the easiest types of locks to install. Rim locks are installed on the face and the frame of the door, using screws, nails or fasteners.
Replacing rim for 2006 cobalt?
To replace the rim on a 2006 Cobalt, you'll need to ensure the replacement rim matches the same size, bolt pattern, and offset as the original rim. You can purchase a new rim from an auto parts store, online retailer, or a dealership. It's also recommended to have a professional mechanic install the new rim to ensure proper fitment and alignment.
What formula is used to determined the contact area of a drum without a rim?
D2x0.785
Vibrating steering wheel at 40 MPH?
Your rims are bent and/or your alignment is off. Bent rim, bad tire, loose suspension/steering component.
Do bad rims cause bad alignment?
The short answer is yes. The rim itself can vibrate excessively on the axle which could loosen the components which maintain the alignment. This could happen gradually and go unnoticed for awhile. Chances are better bad tires can vibrate which is why they are balanced upon installation. Your tire dealer should be able to differentiate between a damaged/bent rim and a bad tire.
What are some causes of Chevy impala to shake on acceleration?
Bad CV joint. Bent rim. Needs alignment. anything relating to your wheels could be the cause.
What is the most common problem from hitting a giant pothole?
Throwing your alignment out or busting a hole in the oil pan or losing a hubcap or blowing out a tire or bending a rim.
Will 22 inch fit on 1996 z28?
Not without suspension modification. Check with speed shops and parts stores for complete mod kits that will allow that rim size to work. Also be aware that will raise the vehicle's ride height and effect alignment. Normal alignment specs will not work with the modification and a speciality alignment shop should be consulted.
