0
What else can I help you with?
How the load shifted from one point to other point using couple?
A load may shift from one point to another point using a couple because the couple or strapping is not tight enough.
How do calculate working radius of a crane?
calculate radius of crane: The radius is always measured from the centre of rotation and is the radius measured after the boom deflects forward when under load.
What is a load balancer?
It's a weight equal to a load, used to balance that load.
What size steel I beam do you need to carry a 5000 pound point load with a span of 20 feet?
To determine the appropriate size of a steel I-beam for a 5,000-pound point load over a 20-foot span, you'll need to consider factors such as the beam's material properties and safety factors. Typically, a W8x10 or W10x12 I-beam might be suitable for this load, but it's crucial to perform detailed calculations or consult a structural engineer to ensure compliance with local building codes and safety requirements. Additionally, factors such as beam support conditions and deflection limits should be considered in the final design.
What are the advantages and disadvantages of token ring?
Advantages of token ring: A point to point digital simple engineering, standard twisted pair medium is economical and easy to install, easily detected and corrected in case of cable failure, short frames as no padding of data is required in frame, works best even with heavy load. Disadvantages are: Require a monitor function, substantial delay in cases of low load, can require more wire to run than a bus architecture.
What are cut-off and saturation points in a dc load line?
The cut-off point is the exact point where the load line crosses with the vector axis. The saturation point is the point where the load line intersects with the collector current axis.
What is the bending moment diagram for a simple supported beam with udl and a point load not in the centre of the span?
The answer is not formulatic. There will be a parabolic shape from the dead load and a discontinuity at the point load.
What is difference between AC and DC load line?
A dc load line is formed by joining the 2 points wherin the slope is equal to the inverse of the load resistance.. whereas the ac load lin has a different slope... and it intersects the dc load line at the quiescent point.
What is the meaning of quiescent point?
it is a point on a load line where no signal appears
What is meant by the term load centre as it applies to truck?
The term "load centre" in relation to trucks refers to the point at which the load's weight is evenly distributed across the truck's axle. It is crucial for ensuring stability and balance while the vehicle is in motion. A proper load centre helps prevent tipping, improves handling, and ensures safe operation, especially when navigating turns or uneven surfaces. Understanding the load centre is essential for effective weight management and compliance with safety regulations.
Difference between dc load line and ac load line?
well the difference mainly exists in the method of finding them , these are :-1. in finding DC load line :-open all AC sourcesopen all the capacitors2. for AC load line:-open all the Dc sourcesshort all the capacitors.
What is an operating point of dc load line?
operating point of dc load line refers to point where there is no signal either no amplification use to take place as base current is zero(in case of common emitter configuration) and it is represented by Q.......
How do you choose q point on load line?
the fixed amount of current and voltages are developed across the transistor is called biasing. thus the fixed voltages and current developed are called Q-point
what is the deflection of a simple supported beam with point load?
Deflection of simply supported beam is given by P*l^3/(48E) Where P= point load at centre of beam l= length of beam E= Modules of elasticity
How do you draw DC load line and determine the Q point?
we should be take two point from the the graph between collector current and emitter-collector voltage.. along the horizontal line collector current is zero and emitter-collector voltage become Vcc,and along the vertical line emitter-collector voltage is zero and collector current become Vcc/RL then by this line that drow between this two point is called load line that in this line the transistor allowed to operate....
Aim of load line analysis of a transistor amplifier?
to achieve quiecent operating point
What is the use of load line?
It helps us to select the Q - point of the BJT, MOSFET etc.
