0
1 1/3 inches and each spacer must be 2/3 inches thick.
Formula is 1 1/3 divided by 2/3 if you recall in fractions when dividing you cross multiply. In this equation 1 1/3 turns into 4/3 divided by 2/3 when you cross multiply it becomes 12/6 which is equal to 2, so you can cut 2 spacers from the tube that will equate to 2/3 inches thick.
What else can I help you with?
What is the next three numbers in the pattern 354555?
The number 5 is used as a spacer (sp) in the sequence. 3-sp-4-sp-5-sp-6-sp-7-sp.....
How do you find out how much tile you would need for a 242 sq ft room?
find the dimensions of each type of tile used. (LxW) length and width multiplied together is area. This concept is useful to putting information into a common form. The form we are seeking is 'how much tile for a xxx square foot room.' So our answer we are seeking is in square footage. Most tile will be small enough to measure in inches with a tape measure. Again if we were to apply this perfectly from a mathematical standpoint, we would not take the dimensions for each tile that is written on the box, and have to account for grout spacers (typically 1/4 to 1/8 of an inch). In this case we would measure each tile's length and width then add 2 times the spacer gap to both the length and width. L+2(1/4) = calculated length, and W+2(1/4) = calculated width. Then multiply both together to get your tile area. Keep in mind we want sq ft, and have measured in sq inches. There are 12 inches in one foot, and 144 inches in one square foot. So we then multiply our answer by 144 to get square footage. Now we have the area of a tile in sq feet. We know we need 242 sq ft to cover so divide that by the area of our tile. The units will cancel (for math geeks conscience) giving us a unitless answer for the amount of tile. In real life we are estimating amounts of tile since we don't buy them individually. Since we are looking for a good estimate to we have enough to get the job done, but not so many we run out of money we will make assumptions. The dimensions of the tile written on the box will be taken literally, and we will not account for grout spacing since it is not large enough of a factor to dictate another box of 200 tile. If we were to use 4x6 in tile, that comes in packages of 150, here is the example of how we would do so: 4*6= 24 in^2 = A [in^2] 24 [in^2] * [ft ^2/ 144 in^2] = 0.167 sq ft = A [ft^2] 150 tiles * 0.167 [sq ft] = 25 sq ft in each package 242 sq ft / 25 sq ft = 9.68 packages Since we cannot buy 0.68 packages we will round up and have spares. we will buy 10 packages of tile to cover our square footage of 242. That will end up being 9.68*150 = 1452 tiles OR in our case of ten packages, 1500 tiles.
How do you keep 3 slat fence straight?
To keep a 3 slat fence straight, start by marking a straight line along the desired fence line using stakes and string or a level tool. Ensure each post is set at equal intervals and is plumb using a level before securing it in place. As you attach the slats, use a spacer to maintain consistent gaps between them and check their alignment frequently. Finally, reinforce the structure by adding cross-bracing if needed to prevent warping or leaning.
How do you miter outside corners on beveled siding without a compound miter saw and what are some helpful tips?
I'm not sure I understand the material your using. I'm assuming it is wood. IF so, don't miter them unless you have a good supply of valium. Take two pieces of 5/4" and rip them down to make a corner. The siding will dive into the corner and look good. All straight cuts, no valium. BCLEAR. If your saw has a big enough blade, lay siding flat, face up on saw. You place spacer piece, that is the same thickness of the butt of the siding, under the thin edge of the siding, to mimic how it would lay on the wall, then cut a 45deg. miter. Test & adjust w/ scrape pieces till you get it right.
I need To turn the distributor cap on a 350 1985 a quarter turn to the right so the air filter will fit but every time i do that the engine wont start what should i do and how can you do it right?
If you are slackening the clamp and swinging the dist round quarter of a turn it is throwing the ignition timing right out. You have to remove the distributor completely from its drive and turn it, then replace. You can set the finer timing with a strobe light. answer move wires back 2 terminals counterclockwise Answer Get a smaller diameter air filter. Answer: The reason your engine wont fire is that you are putting your ignition advance out of time. Play with your distributor until your vehicle runs properly and tighten your bolt down and leave that as it is. Now what you must figure out is how to get your air filter on. You can put a Throttle body spacer on to position your carb a little higher. Or you could go and purchase a different air filter holder and a new air filter that will fit on your engine. Take your time if your purchasing a new holder because you dont want to waste your money get something that looks good and is functional. I prefer edelbrock stuff so i would go with edelbrock and probably a K&N filter. Anyways yeah your problem is you are screwing with your spark advance.
What is the function of spacers in gear box?
Spacer is used to maintain the distance
How much does it cost to have a teeth spacer?
nothing. the cost is the thing you do after spacers.
Where can you find a spacer for your monroe piercing?
Any body piercing studio will carry spacers.
What sweet treats can you eat with spacers?
I had a spacer and all the dentist said was that meat could get stuck in it
Would it hurt to yank your spacer out?
I would say yes because it hurts for me to even chew my spacers.
What are round plastic or metal pegs that separate the motherboard from the case?
the name for these is standoffs or spacer.
Do they make Spacers for Bricks?
You can find Masonry Block and Brick Spacer's on the Internet. They really are a big help for the DIY'er, Handyman and Homeowner.
What information can I find in the Shimano BB spacer chart?
The Shimano BB spacer chart provides information on the specific sizes and configurations of spacers needed for bottom bracket installation. It helps users determine the correct spacer setup for their specific bike frame and crankset compatibility.
When do you change from spectacle blind to spacer and spade?
When you have space constraints for the positioning of the spectacle blind, then you can consider using spacers and blinds (which have just a handle)
What is the function of spacer in electrical transformer?
Spacers insulate the transformer tank from the mechanical vibrations of core & the windings.this results in reduced noise emisions.
How do you put spacers in your ear lobes?
To put spacers in your ear lobes, first make sure your ears are clean and disinfected. Next, gently stretch your ear by slowly inserting a spacer or taper into the piercing until comfortable. It is important to be patient and not force the spacer in, as this can cause damage to your ear lobes.
What does a orthodontic spacer look like?
Spacers look like blue/ purple mini rubber bands stuck in a place for braces.... Almost everyone has to get spacers before braces
