0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is a geometric figure that shows all possible angles?
The number of all possible angles is infinite and no figure can show them all.
How you remove positive zero error?
Positive zero error means, instead showing zero it shows some value more than zero. Hence positive. Suppose if it shows some reading say 0.03 units. then while correcting we have to subtract the above from the observed reading. So correction is adding negative error.
What is zero error in physics?
Zero error is defined as the condition where a measuring instrument registers a reading when there should not be any reading. In case of Vernier calipers it occurs when a zero on main scale does not coincide with a zero on Vernier scale. Source: calculatored and written by Shaun Murphy
If a thermometer shows a negative of -20 degrees and the temperature rises to -10 how much will it have changed?
A change in the reading of a thermometer from -20 to -10 degrees represents a rise in temperature of 10 degrees. Another way to say this is that the temperature changed by +10 degrees.
What does a circle have to do with a pi?
Most pies are circular. Okay, that was a cheap joke. The actual answer is that pi is the ratio of the diameter of a circle to its circumference. That means it shows up a lot in equations involving circles and circular things. It also shows up in a lot of places you might not initially expect. For example, the sum of the infinite series 4 - 4/3 + 4/5 - 4/7 +4/9 ... is Pi.
You can put direct power to your solenoid and it starts The wire you pulled off the solenoid shows power from the swith but wont start it?
Defective solenoid?
Who is responsible for the reading of the will?
There is no requirement for a reading of the will. That is a fiction from movies and TV shows.
What is the standard reading in megger testing to conclude that the equipment is passed and or failed?
Meggers send voltage thru the cables to determine the resistance between, meggers like the mj145 have multiple settings from 100 volts to 1000v, a Megger showing a good reading will show megaohms thru its full band, a bad one reading will be indicated by it either reading 0 ohms or less then 30 ohms (depends on the circuit and what's between the wires) a bad indicator can also be a steady reading at low voltage then at higher voltage it spikes to a low ohm, or a low voltage, like as if u just created a short. What that shows is at low voltage your insulator is fine, but at high voltage it blows thru it, normally that means your Insolator around your wire is damaged.
Infinite resistance in one direction of Diode?
After isolating the diode from the circuit, the diode shows infinite resistance in one direction and low resistance in the other direction. The diode
Where is the starter solenoid on a 2005 ford explorer?
The starter solenoid shows to be on top of starter. If you don't know where the starter is located, follow the positive battery cable. You may have to get under vehicle to get at the starter. I replace starter and solenoid as a unit. Now, if your talking about starter relay that is a different animal.
Where i do put a apostrophe in mark was reading his grandfathers journal?
The correct placement of the apostrophe is: "Mark was reading his grandfather's journal." This shows that the journal belongs to his grandfather.
When a thermometer is kept in the ice the reading shows?
Increases first and then decrease
What is a geometric figure that shows all possible angles?
The number of all possible angles is infinite and no figure can show them all.
What is the reading of ammeter when battery is low?
it shows some reading even though battery is low because of there will some flux remains in the magnets
What is the preposition word on Joseph was reading a book in the library?
the preposition in that sentence is [in]
Which proof reading mark shows that you want to delete a word?
Check https://proofreadmyessay.co.uk/
On a 2001 aztek does anyone know the amps or ohms that the plug should be reading that connects to the EGR Valve you put a new one in and the computer still shows an EGR valve problem?
I searched my DVD and i cant find any specifications but looking head on at harness ends from the right whihc is cavity A to left which is cavity E these are the wires- A GRY 435 EGR Solenoid Low Control B BLK 2753 Low Reference C BRN 1456 EGR Solenoid Position Signal D GRY 2702 5 Volt Reference E RED 1676 EGR Solenoid High Control
