0
Add your answer:
Earn +20 pts
When you add two vectors together what do you get?
You get a third vector.
What is one third more than 2400?
One third of 2400 is 800, add this to your 2400 and you get 3200.
What is twenty add one third?
20 1/3
What is one third add one ninth?
13 ninth
How can you change 1 and one third as an improper fraction?
if you get the whole which is 3 and add one third equals 4/3
Is there a way you can add 5.1 audio to Auxiliary Inputs?
Auxiliary inputs to a receiver are always stereo. If you have a 5-channel analog signal (from a computer or other multi-channel device), you will need a receiver with a 5.1 analog input. This has 5 separate RCA inputs for left, right, center, sub, and the two surround speakers. An analog output from a VHS-Hi Fi VCR can be input into the stereo aux inputs of a receiver and decoded to Dolby Surround, but this format is actually only 3 discrete channels, left, right, and surround. It has no separate information for the sub or the center channel, and has a limited bandwidth on the surround channel.
What kind of computer speakers can I buy for $100.00?
You will need a multi-channel speaker that can add extra clarity to the bass of the speakers. Paying approximately hundred dollars for this type of speaker is possible.
What size amp do you need for 6 and a half Sony speakers that has 190 Watt peak power and 40 rms and Sony 6 by 9 speakers that has 300 Watt peak power and 60 rms?
200 RMS 4 channel or 2 channel so u know add the rms of the speakers to find the amp rms needed
If my car has eight factory speakers do I need to buy a CD player that has 8 channels?
You can buy a 4 channel cd player and add a crossover and amplifier.
What is channel encoder?
basically in channel encoding we used to add redundant bit(additional bits) into the transmitting signal so to make it robust against the errors that may be occur during its transmission and receiver these error can be detected and corrected when this signal is passed through channel decoder
What is multi channel?
basically in channel encoding we used to add redundant bit(additional bits) into the transmitting signal so to make it robust against the errors that may be occur during its transmission and receiver these error can be detected and corrected when this signal is passed through channel decoder
What is Multi- channel Encoder?
basically in channel encoding we used to add redundant bit(additional bits) into the transmitting signal so to make it robust against the errors that may be occur during its transmission and receiver these error can be detected and corrected when this signal is passed through channel decoder
How do you add a third tv to your dish network?
You can get your satellite signal to a third TV by 1 or 2 ways. The first would be to have a receiver connected to that TV. The receiver would be extra per month. The second manner would be to mirror (splitting the signal from the recever) the 3rd TV with one of the other TVs.
If you buy a home theatre system will you be able to add more speakers to it separately?
I think so, Yes In most cases, yes! But you need to notice the limitation for each systems (in most cases, the central one), say the total output channel of speakers.
What type of speakers qualify as DJ equipment?
Quality DJ equipment starts in the range of 800 watts per channel and above. Companies producing these speakers are QTX, Ekho and Ibiza. DJ equipment also has lighting and special effects to add to the music.
Can you attach additional speakers to the Bose 123 system?
In short, yes. you can add speakers to nearly ANY setup. however, you should be sure to add enough speakers with particular resistance (load/ohms) ratings in order to wire them in parallel and series so each channel has the same total ohms as the original speaker. If the total load on each channel is too high or too low, you could risk overheating the power source (head unit/amplifier), some headunits or amplifiers have built in safety mechanisms which turn off the unit if the load is either too high or too low. Keep in mind, when adding speakers, the power from each channel is split between them. For example, each speaker may get 100 watts, but if you add a speaker to each channel, each speaker will only get 50 watts. Not only this, but keep in mind Bose made some very specific connectors so you will have a hard time to add and connect the extra wires. The system is in no way made for this.
What is a sound system?
Stereos use basic left and right speakers. In 4 channel stereos the add in 2 more channels to move the sound around you. In 5 channel surround they add a center channel for voice coming from a picture generated in from of you. Helps pull you to the person talking on the screen. 5.1 utilizes this and then adds the .1 which is an effects speaker, the subwoofer. Then you feel the roar of an engine taking off.
