0
What else can I help you with?
How loing is a wier reaqching from the top of a 20 feet pole to a point on the ground 14 feet from the base of the pole?
Use Pythagoras' theorem to find the length of the wire:- 202+142 = 596 and the square root of this is the length of the wire which is about 24.4 feet
Do the automotive industries use steel wire?
The automotive industries use steel wire
How can you use mental math to find 3 times 122?
3 x 1 = 3 3 x 2 = 6 3 x 122 = 366
How do you use a factor tree to find prime factorization of 244?
(244) = 2 * (122) (122) = 2 * 61 so prime factors are 2, 2, 61
Why do you use 1 m wire in meter bridge?
It's not necessary to use 1 m of wire. Any length can be used.
Do you need 3-wire romex to feed bedroom ceiling box by electrical code?
No, you can feed it with a 2 wire Romex + ground. It depends on what is mounted on the ceiling. If it is just a light all you need is 2 wire + ground Romex. However if it is a fan/light and you want to control each one independant of the other you will need to use 3 wire Romex + ground. This is of course if you have 2 seperate switches. You would then connect the red wire to the blue light wire and the black wire to the black fan wire. If you use 2 wire Romex just connect the blue and black fan/light wire to the black wire in the ceiling box.
How loing is a wier reaqching from the top of a 20 feet pole to a point on the ground 14 feet from the base of the pole?
Use Pythagoras' theorem to find the length of the wire:- 202+142 = 596 and the square root of this is the length of the wire which is about 24.4 feet
How can I effectively use electrical fish wire for fishing wires through walls and ceilings?
To effectively use electrical fish wire for fishing wires through walls and ceilings, first, locate the starting and ending points for the wire. Next, attach the fish wire to the wire you want to pull through. Then, carefully feed the fish wire through the wall or ceiling, using a twisting motion to navigate obstacles. Finally, once the fish wire reaches the desired location, gently pull it through while guiding the wire you want to install.
How can I run a wire through a wall?
To run a wire through a wall, you will need to first identify the path you want the wire to take. Next, use a stud finder to locate any obstacles like studs or pipes in the wall. Then, use a drywall saw to create a small hole where you want the wire to go through. Feed the wire through the hole and use a fish tape or wire snake to guide it through the wall to the desired location. Finally, patch up the hole with drywall compound and sand it down for a smooth finish.
How can I effectively fish wires through walls?
To effectively fish wires through walls, use a fish tape or wire snake to guide the wire through the wall cavity. Start by creating a small hole in the wall near the starting point and carefully feed the fish tape or wire snake through the hole. Use a stud finder to avoid obstacles and guide the wire to the desired location. Be patient and gentle to avoid damaging the walls or the wire.
What size wire to use to install a thermostat?
Use what is called bell wire or thermostat wire.
Can you use aluminum wire to feed an electric range?
Yes, if the guage/current capacity is right. Make sure all the components that will connect to the wire such as outlet and breaker are approved for aluminum. Check your local electrical code to make sure it's allowed.
How do you wire a 3-way switch with the feed and switch leg at one end of the threewire and feed out 110v at the other end?
Send an E-mail to me and I will e-mail a simple drawing. Make certain that you put a title on the e-mail that distinguishes it from "spam", since the address that I use is my "throw-away" account, and most of the stuff that goes there gets tossed into the bit bucket.
Do you need winzip to use GTA VC trainer?
122
What kind of welding machine do you use to weld your muffler?
I would use a wire feed MIG, or a oxy-fuel torch. If arc welding, use a low power. It's really easy to burn through exhaust pipes and mufflers.
How do you wire a hei?
The only thing needed to wire HEI is a good positive wire. It needs to be from a wire that is "hot" when the key is turned on...but not when it's off. Use 10-12 gauge wire. Nothing smaller than 14. Run that wire to the positive side of the coil/cap. There are two possible places to run this....but you will find one is marked "tach". That's for the signal feed for a tachometer. Everything else in an HEI is self contained.
Why use 3 wire 240 volt receptacle instead of a 4 wire 240 volt receptacle?
Use the 4 wire if possible. You would only use a 3 wire for an old appliance.You shouldn't if possible. The 3 wire has no neutral wire as the 4 wire does. Som applications require the use of a 3 wire and some don't.
