answersLogoWhite

0

1. a,b,c
2. b - results to UCC
3. 1- remove a half sheet of m8 paper... 2-Dip the paper into the liquid 3-Observe the m8 paper for color changes 4-compare any color change 5-report results 6-discard m8 paper
4. d - It changes color
5. a - red
6. b - black
7. a - Exhaled air is directed through the outlet valve and front module covor
8. b - local logistics readiness flight personnel will measure your face length using a caliper
9. b - it will leak causing possible illness or death in a contaminated environment
10. b - sitting erect with your head level, your mouth closed, and your teeth lightly together
11. b,c,e - upon issue, prior to turn-in, prior to deployment
12. d - immerse the mask in the disinfecting solution
13. a,c,e - The threads are damaged. It is dented deeper than 1/4 inch. It is dented on a seam.
14. a - turn in the mask
15. c - 1/4 inch
16. b - replace the harness
17. d - Separation of the silicone from the metal surface to which it's bonded
18. d - turn in the mask
19. a - the straight side of the D-ring on the shoulder strap of the carrier
20. b - incorrect installation may cause toxic agents to leak into the mask
20a. outward
21. b - fit the narrow rib into the groove where the lens and the mask are bonded
21a. a - replace it with a new second skin
22. a - large rib at the bottom, facing outward
22a. a - install the second skin around the drinking tube
23. c - With the front voicemitter toward the open end of the bag
23a. b - force the air out of the bag
24. c - make sure long hair is tied back and hangs outside of your GCE jacket
25. c - Run a finger under each temple tab, front to back.
25a. c - loosen the neck straps
26. c - you perform the negative pressure check and the lens remains deflected after holding your breath
26a. b - by the front of the facepiece
27. a - stop breathing and close your eyes tightly
27a. c - 9 seconds
28. a - determine proper fit -- if the lens remains deflected, this give an indivation of an initial proper fit
29. a - reverse it over the face of the mask
29a. d - place the m50 head first and the m45/mcu-2 filter first and upright facing away from the body
30. d - hook-and-pile fastner tape at the fly
31. a,b,e,f - The manufacture date, part of the national stock number (NSN), the contract number, garment size
32. a,b,e - centered in the middle of the back of the hood, horizontally above the eyelens on the front of the hood, over the right breast of the coat
32a. d,c,e - first and last name, rank, service component

33. d - wash it

33a. a - by marking the labels inside the coat and trousers
34. a - over the combat boots
35. a - outer gloves and glove liners
35a. c - to protect your feet and ankles from contamination

36. c - to protect your feet and ankles from contamination
37. b - Secure all overgarment fasteners on each ankle so that they fit snugly around the protective footwear.
38. c - leather gloves
38a. a - 2 minutes

39. a - 32F

User Avatar

Wiki User

15y ago

Still curious? Ask our experts.

Chat with our AI personalities

LaoLao
The path is yours to walk; I am only here to hold up a mirror.
Chat with Lao
BlakeBlake
As your older brother, I've been where you are—maybe not exactly, but close enough.
Chat with Blake
TaigaTaiga
Every great hero faces trials, and you—yes, YOU—are no exception!
Chat with Taiga

Add your answer:

Earn +20 pts
Q: Cbrne module 3 pre-test
Write your answer...
Submit
Still have questions?
magnify glass
imp