0
What else can I help you with?
How many feet of starter are in a 3 tab bundle?
A standard 3-tab shingle bundle typically contains about 33 square feet of coverage. To calculate the starter needed, you generally require one starter strip for every three bundles of shingles. Thus, you would typically use about 11 feet of starter per bundle, translating to approximately 33 feet of starter for a full bundle of 3-tab shingles.
What is the strip footing formula?
strip footing drawing and plan
What is a fraction strip?
A fraction strip is simply a paper used to find fractions of a whole.
How do you do a twelfth for a fraction strip?
You can fold a thirds strip in half and then in half again and you get twelfths.
What is the math definition for a strip graph?
Represents frequencies as a proportion of a rectangular strip. in Picture or dots
How can I shingle my roof by myself?
First, mark the roof with chalk lines at intervals. You want to make sure that your plumb lines are straight. Lay your first shingle butted up against the outside of the roof and overlapping the starter strip. Nail it down, with one nail at each corner, just below the asphalt line. Lay the next shingle down, and nail it down. Continue to the end of the roof.
What is the perimeter of the Gaza Strip?
See Related Links for map of Gaza Strip.
How many feet of starter are in a 3 tab bundle?
A standard 3-tab shingle bundle typically contains about 33 square feet of coverage. To calculate the starter needed, you generally require one starter strip for every three bundles of shingles. Thus, you would typically use about 11 feet of starter per bundle, translating to approximately 33 feet of starter for a full bundle of 3-tab shingles.
Price to shingle 1000 sq ft roof?
A total strip and repair here runs about $5K
When was Strip House created?
Strip House was created in 2000.
How could you measure the perimeter of a round object using a ruler?
Wrap the strip of paper around the plate or can and mark it where it completes a full circle around the object. Then lay the strip on a flat surface and measure the marked length using the ruler. That length is the perimeter (circumference) of the round object.
If you Walk perimeter of 3 acres equals how many miles walked?
You will have walked about 10.92 miles in perimeter. * * * * * That is a total rubbish answer. An area does not and cannot define a perimeter. An area of 3 acres can comprise an extremely thin strip stretching millions of miles. So the perimeter would also run to millions of miles. And if the strip was thinner, it could be billions of miles or trillions, etc.
How do you take dips out of your roof to put new shingles on?
Strip off the old roofing and decking and replace it with thicker plywood, then apply the asphalt paper and re-shingle.
What would you install first starter strip j-channel or corner piece?
install the corner piece first.. BUT find level line from soffits down to top of starter strip first.allow for a little over hang of the strip below wood surface [but don't "bury" your siding into the dirt]as a rule of thumb I go 3/4 of an inch, then snap a line and then install corners, then install starter strip leaving about 1" from corners, [nail strip] butting your strips together, nailing it tight to wall.
What would you install first starter strip j channel or corner piece?
install the corner piece first.. BUT find level line from soffits down to top of starter strip first.allow for a little over hang of the strip below wood surface [but don't "bury" your siding into the dirt]as a rule of thumb I go 3/4 of an inch, then snap a line and then install corners, then install starter strip leaving about 1" from corners, [nail strip] butting your strips together, nailing it tight to wall.
Driver for tevion film strip scanner the one i have is a non starter?
i need to download a driver for tevion film strip scanner on windows xp
I needed to repair my mom's roof shingles Please help me How do I go about it?
To mend the shingles you require some roof repair materials. They are - roofing cement, aluminum flashing and a flat pry bar. The width of the flashing should be 1 inch lesser than that of the damaged strip of the shingle, and the length should be 4 inches more than it. Take the required measurement of the shingle and cut the flashing accordingly. Then you have to loosen up the damaged strip and the adjacent strips on its both sides with the help of pry bar. Now apply some roofing cement below the shingle where the flashing has to be placed. Insert the flashing under the shingle and put some more cement above it. Finally, put some pressure on the shingle so that it gets attached to the flashing properly. Or better yet, contact a roofing contractor.
