0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Slight convex curve in surface of road?
Surely it must be the camber?
Can their be negative gravity?
Yes, there can be negative gravity. If a gravity is a pulling force then in the other hands a negative gravity would be a pushing force, in other words, the negative gravity would push us to wherever and the positive gravity on Earth would pull us.
What is a negative response to gravity?
The normal reaction to gravity is attraction. Gravity tries to pull the two objects closer together. A negative reaction would be that the two objects try to push apart. Sounds like science fiction.
What is a negative - positive?
Negative * positive = negative Positive * positive = positive Negative * negative = positive
Does a negative plus a negative equal a postive?
No, a negative plus a negative is a negative
Camber adjustment on 2002 Trail Blazer?
lower control arm is where the camber and caster adjustment is. you cannot change camber without changing caster. the vehicle has to be aligned. to answer the ? the front bolt on lower control arm. to raise pull under to lower slide out
How does negative tire or wheel camber work?
Camber is the angle between the vertical axis of the wheel and the vertical axis of the vehicle when viewed from the front or rear. With a negative camber angle the top of the wheels is leaning in towards the vehicle. Tires tend to roll while cornering, and the inner contact patch may lift off the road surface. By using negative camber the effect is reduced, maximizing the tire's grip. This is only effective on the outside tire during the turn, which is bearing the majority of the vehicle's load as the weight transfers opposite of the direction which you are turning.
Why would the tires on a Lincoln Town Car point inwards bottom out?
Excessively negative camber. Assuming that the ball joints aren't fuxor3d, you can adjust the camber using the cams at the upper ball joint.
What causes tire ware on inside 2001 ranger?
Negative camber. If you look at the tires straight on and they look more like this / \ they will ware on the inside. Inversely, positive camber \ / will cause faster ware on the outside. Negative camber could be caused be bad bushings or too much weight in the front. Positive camber comes from either bad bushings or lifting the truck too high without replaceing the bushings. The closer to | | the better...unless you have a baja style truck, but that's a whole different story!
Your 2001 Lincoln ls has a negative camber at the rear of the car the right side has a bit more negative camber than the left side can this camber alignment be adjusted evenly?
the LS rear end specs are -1.00 degree on each side, yet aside from using a frame machine to bend the control arms to the perfect degree, they are non- adjustable...another way for ford motor company to steal our money....
What is skateboard camber?
AnswerIt is the curve of the skateboard deck --also referred to as the concave of the deck.this answer is incorrect ^ camber is an upward ark on the board creating more push when you carve, concave is not the same thing as camberCamber is the arch of the board or deck front-to-back, and concave is the arch of the deck side-to-side. A positive 3% camber with a 2% concave would be a deck that is arched up in the middle higher than the front and back ends by 3%, with the edges along the side folded upwards 2%. Some decks are also flat-camber (flat-wood), as well as negative camber, which means the center is arched lower than the front and back. A negative camber deck is also referred to as "rocker" or "rockered"; surfboards are also referred to in this way.
When you stance a car do you have to add camber to the rims?
Stance is lowering a car and having the lowest profile tire possible on your wheels while tucking at full negative camber. By lowering the car you have already adjusted the camber, normally you would add adjustable camber plates or control arms to align the vehicle properly, this is the opposite for stance, you want to get plates that will go fully negative or control arms manufactured for this. do not attempt to hack your control arms by yourself, the control arms are what keep your wheel, hub assembly attached and if done incorrectly can cause serious damage.
Why are tires wearing out on the inside?
I'm assuming your talking about a vehicle or possibly trailor tires.. Case being, Tires that wear on the inside have a negative camber and tires that wear on the outside have a positive camber. If you would notice a lowered car. 9 times out of 10 the tires are leaning in towards the vehicle. That would be your negative camber only a camber kit would resolve. As for positive camber almost the same scenario. Check tie-rods and control arms. If you don't see anything wrong and didn't adjust anything. I'd get it to a shop and have it looked at. If we're talking about a trailer with no weight on it. It is possible for this to happen due to heavier suspension and no weight to balance it.
What could cause the rear tires to go inward and wear on the inside on a 98 civic ex?
Rear end is out of alignment. Have a 4 wheel alignment performed. If the tires are leaning inward on the bottom they should wear on the outside of the tire. This is positive camber. If the tire is leaning in at top and out at the bottom it is called negative camber. Independent rear wheel suspensions can make differences in camber visible for several reasons. Extra weight will cause most independent rear suspensions to squat forcing the tires out at the bottom ( temporary negative camber ) Early VW Bugs and buses had a suspensions that moved from 0 camber(wheel straight up and down to positive camber (rear wheels moved closer to one another at the bottom) The late 60s VW (68 on) had rear suspensions that went from straight up and down to wheels that were further apart at the bottom (Negative Camber). Weak or worn out rear suspension components such as springs can cause unwanted camber settings. Perhaps a problem with the front caused the tire wear that became visible when fires were rotated . It is quite possible to have the correct camber settings but because of a faulty suspension the alignment specifications become irrelevant.
When was Camber the Heretic created?
Camber the Heretic was created in 1981.
When was Camber Corporation created?
Camber Corporation was created in 1990.
When was Saint Camber created?
Saint Camber was created in 1978.
