0
What else can I help you with?
How do you draw a circle in assembly program?
You can draw a circle in assembly program by using a compass-like tool. Secure the tip of the compass and then rotate the compass tool so that it completes the circle.
What tool do you use to draw a circle?
It is called a compass. No, not like the kind with North, West, etc. but the math type. In most cases, you might hold your finger down in a certain place on the compass to keep it steady, then put a sharp pencil in a little hole (the closer to the center, the smaller your circle), and draw a circle with the pencil still in the hole. Hope this helps!
How do you write absolute value?
Draw parentheses expect draw them up and down instead of curved. It look like this: lXl (on the computer I used lowercase L's for lines)
Is it possible to build a triangle with side lengths 7 9 12?
Yes, since 7+9 > 12. If you want to construct one, you need a compass (the kind that draws circles, not the one that tells North) and a ruler.Measure off 12 units (centimeters, inches, etc.) Pick a point a and label it A, and draw a circle with 12 unit radius, using point A as the center.Next, set the compass to 7 units, and using the same point A as the center, draw a 7 unit radius circle. Next, pick a point on the edge of the 12 unit circle, and label it B. Set the compass to 9 units, and draw a circle centered at B. Draw a line segment from A to B (this is the 12 unit side). Find where the 9 unit circle intersects the 7 unit circle (there will be 2 points of intersection). Label one of these two points as C. Draw a line segment from B to C; this is the 9 unit side. Draw a line segment from point A to C (this is the 7 unit side). On the related link, there is a JPEG of what this would look like.
What is a compass in Geometry?
A compass is a tool used to make a circle. It keeps the writing utensil a fixed distance from the center point. It can come in many forms, from a piece of string tied and held in place, to the more traditional compass that looks like two pencils glued together at their erasers. Other models stay on the paper and use a rotating disk to draw a perfect circle.
How do you draw a circle in assembly program?
You can draw a circle in assembly program by using a compass-like tool. Secure the tip of the compass and then rotate the compass tool so that it completes the circle.
What is a good sentence using draw?
I like to draw pictures of cardinals.
What Name the input device that is shaped like a pen?
This is known as a tablet. It allows you to draw on your computer using a stylus. Also could be a light pen.
Advantages of using a tablet on the computer?
Using a tablet allows you to do draw, sketch and paint much more easily and naturally than using a mouse. You can use it like you would a pen, giving you much better control.
How do you pass the labyrinth?
By using navigational tools like map, compass etc.
How do you make an angle of 150 degree with a compass?
To construct an angle of 150 degrees using a compass, you would first draw a ray as the initial side of the angle. Then, place the compass on the vertex of the angle and draw an arc that intersects the initial ray at a point. Next, without changing the compass width, place the compass on the intersection point and draw another arc that intersects the previous arc. Finally, draw a ray from the vertex through the point of intersection of the two arcs to create an angle of 150 degrees.
What is a lensatic compass?
Lensatic Compass is a kind of compass which uses a magnetized dial, a lensatic compass features a special card which helps the users in reading the directions easily. A Lensatic Compass is very useful device because it has numbers which are useful in identifying the directions of target objects. The use of Lensatic Compass involves difficulties in using it.It is important to learn how to use a lensatic compass properly prior to using it, also other materials like a map and a protractor are also needed when using the compass.
What do people do with smart boards?
A smart board is just like a computer but is bigger, touchscreen, and you can draw on it. I really like it.
What is a realtive location?
Is where you give directions by using the compass ross like north south west and east
How do you draw anime on the computer?
manga is the stuff that you draw, like a comic strip. anime is the moving version of manga, basically manga is the drawing anime is the cartoon. you cant draw a cartoon, or if you did, it would be like a flip-notebook imagery cartoon.
How do you draw pie slice in c graphics?
using pie slice function akwinder can draw monkey which exactly looks like her.
What did the Chinese compass look like in 1996?
What did the chinese compass look like in 1898
