0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many fence post needed to fence 18 meters?
It depends on what kind of fence you wish to put up. For example, an electrified barbed wire and steel post fence would only require about three posts. But a wood plank and wood post fence would require about five or six.
A rectangular yard 80 feet by 60 feet has a fence with a post on every corner and another post every five feet how many posts are needed for the entire fence?
56 posts are needed for the fence
How many fence post do you need for a fifty foot diameter circle?
You need 1962.5 fence posts.
How many posts needed for 5 miles of fence with a post every 4 feet?
6600 the correct answer is actually 6601 because you need one more post to close the fence.
What solid figure would you get if you cut a fence post in half?
A rectangular prism or a cuboid.
How deep do you have to dig a hole for a fence post IN CHICAGO?
4'
How do you install cedar fence posts?
You need a post hole digger and cement. YOu have to measure out the area that you are putting the post. YOu can space them apart every 6-8 feet. You dig the hole and have the cement prepared and when the hole is done you put the cement around the post. The cement should come with directions for mix. You should put the post down at least 10" for it to stay in the ground well. I don't think 10 inches will quite do it. A good rule of thumb is half the heaight of the fence but nothing less than 30 inches deep. The diameter of the hole should be at least 4 inches greater in diameter than the post but nothing smaller than 6 inches. Make sure your holes look more like a bell than an ice cream cone because frost in the winter time can actually lift the post out of the ground.
How do you install vinyl fencing from diy?
Buy the fence, dig the post holes, make sure the ground is level, set posts, refill holes, set up the rest of the fence, etc. Hire someone for help if you aren't sure what to do - the last thing you want to do is have an uneven/unsturdy fence.
How deep you should put post in the ground in IL?
It all depends on what the post will be used for. In general 30 to 36 inches should be adequate to support a 4x4 post for a clothesline, a fence or a mailbox. Anything less than that and you most likely will have a problem with frost moving or lifting the post to the point where it will not be straight in the spring.
What type of 1-man fence post auger is worth the money?
A 1-man type fence post auger is worth the money if it is capable of digging a hole efficiency and quickly. These can dramatically reduce the physical strain associated with digging numerous holes.
My neighbor fixed his gate to my fence can I remove it?
His gate really jars my fence when he shuts it. I think he should put his own post in and attach his own gate to his own post.
What direction must the post of a wooden fence face?
to answer that ? is the post is to the inside of the fence
How to Install an Aluminum Fence?
Aluminum fences are sturdy yard fences that often aren’t as difficult to install as chain link fences or wooden stockade fences. This article will show you how to install one in a series of easy to follow steps. oLay out the fence line. This is essentially done by measuring from some reference point (such as your house) with a tape measure and marking the corners and post locations with stakes or markers of some sort. The post locations will be determined by the length of the fence sections. When you have the partial rectangle (or whatever shape) that your fence will describe, you can check it for square by measuring corner to corner. If your fence is square (i.e. corners are 90 degree angles), these diagonals will be the same. Make adjustments as necessary. oDig post holes at the post locations. They should be around 24 inches deep and 18 inches in diameter. To test that the holes are the right width apart take one of the fence sections and lay it next to the holes, checking for correct distance. oSet the posts in the holes. Do this by first mixing some post hole (or any ordinary) cement, putting a small amount in the bottom of the hole, and then setting the post into it. oThen add the cement around the post, filling the hole up until it is a few inches from the top, and stabilizing the post in the cement. Use of carpenter’s level here to check that the post is plumb and level. Slope the concrete up to the post a little at the top for better water runoff. You will fill the remaining space with dirt when the cement is dry. oGo back to the posts and recheck them for plumb and level. It is important that the concrete dries with them standing as straight up and down as possible. oWhen the cement is dry, install the fence sections. With aluminum fences, there will be nuts and bolts that come with the fence that you will use to attach to the posts. oFinally, install the fence gates. These also will screw and bolt on, and shouldn’t be too much harder than the sections. Make sure the gates swing well and latch and lock evenly. That’s it, you’re done! Enjoy your aluminum fence.
What is a strainer post?
A strainer post is a fence post.
What is the definition of a fence post?
A pole that supports a fence.
How do you install fence post?
To install wooden fence posts, it is bests to use a fence post auger. An auger literally drills the correct size hole in which to insert the post.
Has anyone used a fence posts called the z post?
Yes! The Z Post is the best fence post I have ever used! It is a metal fence post for wood fences. Its is powder coated like wrought iron. It is a gret post. HIGHLY Recommend!
