To convert mils to circular mils, you simply square the mil measurement. Since one circular mil is defined as the area of a circle with a diameter of one mil, you can use the formula: Circular mils = (mils)². For example, if you have a wire with a diameter of 10 mils, the conversion to circular mils would be 10², resulting in 100 circular mils.
.000025 circular inches = 25 circular mils
1 Circular mil = 0.7854 x 10-6 Square InchConveter:http://www.unitconversion.org/area/circular-mils-to-square-inchs-conversion.htmlInformation from:http://www.engineeringtoolbox.com/mil-circular-mil-area-d_817.html
To convert the gauge of a wire to circular mils, you can use a wire gauge chart. A 32-gauge wire has a cross-sectional area of approximately 1,000 circular mils. For a 7-strand configuration, the total area would be 7 times the area of a single strand, which would be about 7,000 circular mils. Thus, 7 strands of 32-gauge wire would have a combined cross-sectional area of approximately 7,000 circular mils.
The ddiameter of No. 14 wire is 64 mils. What is its area in CM and in SM?
The weight of 250 mcm (thousand circular mils) copper per foot can be calculated using the formula: weight (lbs/ft) = (circular mils × 0.000001) × 0.321. For 250 mcm, this results in approximately 0.196 lbs per foot. Thus, 250 mcm copper wire weighs about 0.196 pounds for each foot of length.
1 circular mil = 1 mil x 1 mil a=d2 so if a wire has a diameter of 80 mils, it has an area of 6400 circular mils.
.000025 circular inches = 25 circular mils
The cross-sectional area of a 12 AWG solid wire is approximately 6530 circular mils. Circular mils are commonly used to measure the cross-sectional area of wires and cables in electrical engineering.
1 Circular mil = 0.7854 x 10-6 Square InchConveter:http://www.unitconversion.org/area/circular-mils-to-square-inchs-conversion.htmlInformation from:http://www.engineeringtoolbox.com/mil-circular-mil-area-d_817.html
To convert the gauge of a wire to circular mils, you can use a wire gauge chart. A 32-gauge wire has a cross-sectional area of approximately 1,000 circular mils. For a 7-strand configuration, the total area would be 7 times the area of a single strand, which would be about 7,000 circular mils. Thus, 7 strands of 32-gauge wire would have a combined cross-sectional area of approximately 7,000 circular mils.
CMA (Circular Mil Area) is a unit used to measure the cross-sectional area of a wire. In the context of electricity, CMA range is the range of wire sizes expressed in circular mils that is commonly used for various applications, such as power transmission, wiring, and electrical installations. This range typically varies from a few thousand circular mils to several million circular mils.
MCM (thousand circular mils) and KCM (kilo circular mils) are both units used to measure the cross-sectional area of electrical conductors. MCM is equivalent to one thousand circular mils, while KCM is equivalent to one thousand MCM, or one million circular mils. Essentially, KCM is a larger unit, used for measuring very large conductors, whereas MCM is more commonly used for medium-sized cables. The choice between them often depends on the size and application of the cable in electrical systems.
MCM is another measure of wire gauge. It is somewhat confusing but it starts at around 40 gauge being the smallest wire up to the largest gauge of 1. from there you have oughts which is from 1 to 4 (1 ought, 2 ought etc) and then you have MCM which is circular mils. MCM can range from something as small as 250 mcm up to 2000 mcm.Another AnswerThe abbreviation, 'MCM', stands for 'thousand circular mils'. A 'circular mil' is a North-American method of measuring the cross-sectional area of a circular-section conductor (Europeans use square millimetres for conductors of anyshape).A 'circular mil' is obtained by squaring the diameter of a circular-section conductor, expressed in mils. A 'mil' is one-thousandth of an inch. As the constant, 'pi', isn't taken into account, it should be obvious that a circular mil is, therefore, a figure representing a cross-sectional area, rather than a true measure of that area.If necessary, in order to obtain a true cross-sectional area, circular mils can be converted into square mils.
MCM is another measure of wire gauge. It is somewhat confusing but it starts at around 40 gauge being the smallest wire up to the largest gauge of 1. from there you have oughts which is from 1 to 4 (1 ought, 2 ought etc) and then you have MCM which is circular mils. MCM can range from something as small as 250 mcm up to 2000 mcm.Another AnswerThe abbreviation, 'MCM', stands for 'thousand circular mils'. A 'circular mil' is a North-American method of measuring the cross-sectional area of a circular-section conductor (Europeans use square millimetres for conductors of anyshape).A 'circular mil' is obtained by squaring the diameter of a circular-section conductor, expressed in mils. A 'mil' is one-thousandth of an inch. As the constant, 'pi', isn't taken into account, it should be obvious that a circular mil is, therefore, a figure representing a cross-sectional area, rather than a true measure of that area.If necessary, in order to obtain a true cross-sectional area, circular mils can be converted into square mils.
square millimetres.AnswerIt depends where you live.In Britain and Europe, the standard measurement is the square millimetre (mm2)In North America, circular-sectioned conductors are measured in circular mils (CM) or multiples (e.g. MCM -thousand circular mils). A circular mil is derived from the diameter of the conductor, in mils (thousands of an inch) squared -so it isn't really a true unit of area (as the constant, pi, isn't used), but simply a number that represents an area.
750,000 circular mils. A wire that is 1 mil (.001 inches) in diamter is defined to have an area of 1 circular mil. The area in circular mils = (diameter in mils) ^ 2. To convert this to area in square inches, multiply 750,000 * pi / 4,000,000 = 0.589 sq in.
It is a wire size, the equivalent cross sectional area in thousands of circular mils. e.g. 500 MCM or kcmil = 500,000 circular mils. The circular mil is a unit of area used especially when denoting the cross-sectional size of a wire. It is the equivalent area of a circle whose diameter is 0.001 (10-3) inch. AWG stands for American Wire Guage.