0
Because Corresponding Parts of Congruent Triangles, there are five ways to prove that two triangles are congruent. Show that all sides are congruent. (SSS) Show that two sides and their common angle are congruent. (SAS) Show that two angles and their common side are congruent. (ASA) Show that two angles and one of the non common sides are congruent. (AAS) Show that the hypotenuse and one leg of a right triangle are congruent. (HL)
What else can I help you with?
What is the measure of angle bdc?
To determine the measure of angle BDC, additional information is required, such as the relationship between points B, D, and C (e.g., if they form a triangle, if there are any parallel lines, or specific angle measures). Without this context or specific values, it's impossible to calculate the measure of angle BDC accurately. Please provide more details or a diagram for a precise answer.
What is the comparison of the volume of space between the piston's top surface and the top cylinder at BDC and TDC is called?
The answer is Compression Ratio. You should try reading the Study Unit it really helps!
What is the BDC of a 180 grain 308 bullet at 400 yards?
The ballistic drop compensation (BDC) for a 180 grain .308 bullet at 400 yards will vary based on several factors, including the specific bullet type, muzzle velocity, and environmental conditions. Generally, a 180 grain .308 bullet will drop approximately 12 to 16 inches at 400 yards, depending on the load and conditions. It's essential to consult a ballistic calculator or specific load data for precise measurements tailored to your setup.
How do you draw a square in six different ways?
Draw one side of the square and label it A.Suppose the other three sides of the square are B, C and D.You can draw these in orders:BCD, BDC, CBD, CDB, DBC and DCB. Six ways in all.Alternative answer:Use a pencil, a chalk, a crayon, a pen, a paint brush, and your finger in the sand.
What is the compression ratio for an engine if each cylinder has a maximum volume of 500 cubic centimeters and a minimum volume of 50 cubic centimeters?
Compression ratio is exclusive to each cylinder, though they will all have the same result if they are the same dimensionally ( and they always are) > Divide the total engine capacity by the number of cylinders, this gives the capacity or swept volume of each cylinder (bore * stroke) > So in a 2.0 (2000 cc) litre 4 cylinder engine, each cylinder has a 2000 / 4 = 500 cc swept volume (bore * stroke) > The combustion chamber is the volume remaining at top dead centre (TDC) > Compression ratio = volume at BDC (swept volume + volume at TDC) / volume at TDC
How do you prove that the diagonals of an isosceles trapezoid are equal?
Let's draw the isosceles trapezoid ABCD, where AD ≅ BC, and mADC ≅ mBCD. If we draw the diagonals AC and BD of the trapezoid two congruent triangles are formed, ∆ ADC ≅ ∆ BDC (SAS Postulate: If two sides and the angle between them in one triangle are congruent to the corresponding parts in another triangle, then the triangles are congruent). Since these triangles are congruent, AC ≅ BD.
How do you prove that the diagonals of an isosceles trapezoid are congruent?
Suppose the diagonals meet at a point X.AB is parallel to DC and BD intersects themTherefore, angle ABD ( = ABX) = BAC (= BAX)Therefore, in triangle ABX, the angles at the ends of AB are equal => the triangle is isosceles and so AX = BX.AB is parallel to DC and AC intersects themTherefore, angle ACD ( = XCD) = BDC (= XDC)Therefore, in triangle CDX, the angles at the ends of CD are equal => the triangle is isosceles and so CX = DX.Therefore AX + CX = BX + DX or, AC = BD.
An exterior angle of triangle BDC is?
<ADB
Can the diffference of two sides of a triangle be equal to less than a third side?
The difference between two sides of a triangle will always be less than the third side.Let ABC be a triangle where AC > AB, extend side AB to point D so that AD = AB + (AC-AB) = AC. Therefore, since AC = AD, triangle ADC is a isosceles where angles ADC and ACD are equal.In the triangle BCD, angle BCD < BDC, Since, angles BCD is part of angle ACD (ACB + BCD ) and angle ACD is equal to BDC .Therefore, using the knowledge that, in a triangle, side opposite a greater angle is always greater than the side opposite a smaller angle, it is proved that, the difference between two sides is always lesser than the third side.In an isosceles, the difference of two sides is zero, since the sides are equal. The third side would always be greater than zero to form a triangle. The same logic can be applied to an equilateral triangle.
If JKL is similar to RST the angles of JKL must be congruent to the corresponding angles of RST.?
Yes that is correct and the sides will be in proportion by ratio to each triangle.
The 5 other names for triangle BCD?
Triangles BDC, CBD, CDB, DBC and DCB.
When Given point b is the interior of angle adc conjecture adb is congruent to bdc.?
False; just because it is in the interior does not mean it is on the bisecting line.
How do you prove that the diagonals and either base of an isosceles trapezoid form an isosceles triangle?
Consider the isosceles trapezium ABCD (going clockwise from top left) with AB parallel to CD. And let the diagonals intersect at O Since it is isosceles, AD = BC and <ADC = <BCD (the angles at the base BC). Now consider triangles ADC and BCD. AD = BC The side BC is common and the included angles are equal. So the two triangles are congruent. and therefore <ACD = <BDC Then, in triangle ODC, <OCD (=<ACD = <BDC) = <ODC ie ODC is an isosceles triangle. The triangle formed at the other base can be proven similarly, or by the fact that, because AB CD and the diagonals act as transversals, you have equal alternate angles.
What does bdc mean?
BDC means Bottom Dead Center
When was BDC Building created?
BDC Building was created in 1972.
What is the measure of angle bdc?
To determine the measure of angle BDC, additional information is required, such as the relationship between points B, D, and C (e.g., if they form a triangle, if there are any parallel lines, or specific angle measures). Without this context or specific values, it's impossible to calculate the measure of angle BDC accurately. Please provide more details or a diagram for a precise answer.
What does bdc stand for on a bank statement?
BDC stands for Bank Debit Card
