0
How do you adjust the top of a 95 LeBaron conv to move it forward so the latch pins line up with the holes in the windshield?
It probably is lined up, but can be very difficult. What you have to do is this:
1. Pull it forward as far as you can.
2. Reach up to the roof at the highest point and pull down, while
3. Pushing forward by the latch.
4. Get one side in but don't lock it in, then repeat steps 1-2 on the other side.
5. Once both latches are in, then lock them.
6. Believe me, this may seem hard, but it needs to be a tight fit. There are some Allen screws that can be loosened to adjust the locks, but think hard before you try... No good deed ever goes unpunished! :)
What else can I help you with?
In a box of 39 buttons 25 have 4 holes 18 are red and 13 have 4 holes and are also red so how many buttons have 4 holes and are not red?
their are a total of 39 14 have no holes at all 25 have 4 holes, 18 of wich are red but only 13 of them have 4 holes so thiers 5 red without holes that leave the other 7 with 4 holes.
What is the formula for pcd dia 100 for 8 holes?
The formula to calculate the Pitch Circle Diameter (PCD) for a given number of holes is: [ \text{PCD} = \frac{d}{\sin\left(\frac{180^\circ}{n}\right)} ] where ( d ) is the distance between holes (or the diameter of the circle on which the holes are located), and ( n ) is the number of holes. For a PCD of 100 mm with 8 holes, you would use this formula to determine the spacing and arrangement of the holes around the circle.
What is the word that means to make holes through?
We can punch or perforate materials to make holes.
What is Four holes and one half as a decimal?
Assuming that you do not mean holes but wholes(!), the answer is 4.5
How many holes are there per square inch in a sieve set?
The size of the holes in a sieve depends on what is the the size of material to be allowed through the holes. A set of sieves (flour sieves, garden riddles, etc) will range from large holes to fine.
How do you adjust the height of the windshield washer fluid sprayer on a 1993 Jeep Grand Cherokee mine sprays almost over the windshield?
the easy way to adjust the sprayers is to use a pin or a needle. look at each sprayer you will see one or two small holes. put the pin in one hole and gently move up or downor side-to-side. the easy way to adjust the sprayers is to use a pin or a needle. look at each sprayer you will see one or two small holes. put the pin in one hole and gently move up or downor side-to-side.
What was special about the boy's name in the movie Holes?
It was spelled the same forward and backwards.
Location of Windshield wiper motor on 2004 Honda CRV?
It is located under the windshield cowl (the plastic cover with the holes in it, directly under the windshield). To expose it - remove the wiper arms, and the retaining nuts on the wiper shafts, then remove the screws holding down the cover.
How do you fix a rear windshield washer sprayer on a 2002 explorer?
I would bet that it's not the tubes but rather the little holes of the sprayers. You may want to take a pin or a needle and see if you can poke any debris (usually hard water deposits or washer fluid 'gunk') from the holes. If that doesn't work you should be able to find the tubing at a parts or hardware store.The hole is generally through a little ball that sits in a socket. If you poke the holes and find that your spray isn't directed at the locations on the windshield that you'd like, take your pin and adjust the ball via the hole to where you'd like the spray to go.
How do you adjust headlight on 94 Ford Probe gt?
When you have the headlights flipped up then you will see 2 holes one on the top and one on the sides. There is a Phillips screw in there that you turn to adjust the headlights.
What happen when Lexus sc400 in drive and it cut off?
All forward movement will cease. If it does not, check for worm holes.
Adjust rear suspension on Honda shadow?
Use the half moon key, sold at Honda dealers for $5. Place on the holes that are drilled at the bottom of the chrome shock. Adjust to the lowest number.
How do you adjust headlights on a 2004 Passat?
Open the hood, & locate two small holes over each headlamp assemply. By inserting a philipshead screwdriver you can adjust vertical & horizontal aming of the headlight.
Whose name is a palindrome in the book Holes?
In Holes, Stanley Yelnats is the character with a palindromic name. (It is spelled the same when read either forward or backward.)
How do you Adjust camber on 1989 Honda Prelude?
you can slot the holes where the upper ball joint bolts to upper control arm.
The staples are flaring out instead of in toward the center. How do you adjust ace liner 502?
Push the bottom plate forward with your thumb so the inward flared staple holes line up with the upper edge of the stapler. That lopsided square place on the bottom of the stapler just slides forwared and backward about a quarter of an inch.
How do you adjust the headlights on a Porsche 996?
Under the front hood and along the side panels you will see access holes near each headlight that you stick a long Allen style wrench through (should be with the car in its tool kit). Turn the wrench within these holes to adjust the beam left to right & up & down.
