0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you calculate the capacity of a rectangle?
A rectangle is a 2-dimensional shape. Therefore, it has no volume - which is what capacity measures.
How do you calculate chilled water system volume if knowing chiller capacity?
just multiply pump capacity by 3
How do you calculate the capacity of a cone?
Capacity or volume of a cone = 1/3*pi*radius2*height measured in cubic units
How do you calculate expected fill rate?
Capacity of container divided by rate of flow
How do you calculate load capacity on 1 inch steel plate floor?
with your face
How do you calculate the capacity of a machine using formula?
how to calculate the embroidery machine capacity and Embroidery factory capacity and efficiency.
What is the difference between effective capacity and design capacity?
Design capacity is the maximum theoretical output of a system. Normally expressed as a rate Effective capacity is the capacity a firm expects to achieve given current operating constraints. Often lower than design capacity
What is the difference between design capacity and effective capacity?
Design capacity is the maximum theoretical output of a system. Normally expressed as a rate Effective capacity is the capacity a firm expects to achieve given current operating constraints. Often lower than design capacity
What kind of capacity refers to the inmate population the institution was originally built to handle?
Design capacity
How do you calculate machine capacity?
how to calculate injection molding m/c capacity
What is design and effective capacity?
Capacity can be refined into two useful definitions of capacity: Design capacity and effective capacity. Design capacity is the maximum rate of output achieved under ideal conditions. Effective capacity is usually less than design capacity owing to realities of changing product mix, the need for periodic maintenance of equipment, lunch breaks, coffee breaks, problems in scheduling and balancing operations, and other similar circumstances.
How do you calculate volume in megapascal liters for cylinders?
First thing, megapsacal litres is a unit of capacity, not volume. To calculate the capacity of a cylinder you first need to know the volume (in litres). Volume = py (3.14159) multiplied by r2, multiplied by the height (or length whatever the case may be). Capacity is then obtained by multiplying the internal volume of the vessel (in litres, L) by the design pressure (in megapascals, MPa). That is: Capacity (MPaL) = design pressure (MPa) x volume (L) To convert pressure in pounds per square inch (psi) to Mpa: 1 megapascal = 1000 kilopascals (kPa) 1 psi = 6.89 kPa Therefore, if design pressure is provided in psi then: design pressure (in Mpa) = design pressure (in psi) x 0.00689 Example: Assume your air receiver has a volume of 140 litres, with a design pressure of 160 psi. design pressure (MPa) = 160 x 0.00689 = 1.100 MPa (1,100kPa) Capacity = 1.100 x 140 = 154 MPaL
What is the formula for calculating the Bearing Capacity?
Bearing capacity of soil= Load carried by soil / unit Area Definition : The safly retained capacity by soil is termed as SBC(Safe Bearing Capacity) of soil. While you design a footing , it is the main factor to consider . To calculate the area of footing Area of footing = load/ SBC
How calculate wire rope load capacity?
Wire rope load capacity can be calculated by considering factors such as the breaking strength of the wire rope, the design factor for the specific application, and any additional safety factors required. The formula typically used is: Load capacity = (Wire rope breaking strength / Design factor) - Weight of the load. It is crucial to consult industry standards and guidelines when determining load capacity to ensure safety and reliability.
How do you calculate the bsc zte bsc capacity in erlang?
I want to know how to calculate the Capacity (Erglang) of one BSC in GSM
How do you calculate chilled water coil using ADP?
To calculate the chilled water coil capacity using the airside performance, you would divide the airside thermal capacity by the ADP (Approach Design Point) temperature difference. This will give you the required chilled water flow rate to meet the cooling load of the airside system.
How do you calculate cooling capacity?
boi
