0
What else can I help you with?
How do you draw the radius of a circle?
A line of any length may act as the radius of a circle. The radius is the distance from the centre to the perimeter of a circle.
What is a radiu s of a circle?
If you draw a line from the center of a circle to the edge of a circle, you have drawn the radius of the circle. If you draw a line from the edge of a circle through the center of the circle and on to the edge on the opposite side, you have drawn the diameter of a circle. The radius of a circle is one half the diameter of a circle.
What does a chord look like in math?
When you draw a circle in math, and you draw a triangle inside of it, 2 of the lines should be the radius of the circle, and the third (bottom) line that is not the radius is the chord.
One radius of a circle is the same length as any other radius of any other radius?
The radius is the distance from the center of the circle to its edge. No matter how you draw this radius, it is one value of one length only, for any given circle.
How do you make circle inside circle in mswlogo?
To draw a circle inside another circle in MSWLogo, you can use the REPEAT command along with the CIRCLE command. First, use the CIRCLE command to draw the outer circle, then adjust the pen position to the center and use the CIRCLE command again with a smaller radius for the inner circle. Here's a simple example: CIRCLE 100 ; Draw outer circle with radius 100 PENUP SETXY 0 -50 ; Move to inner circle position (50 units up) PENDOWN CIRCLE 50 ; Draw inner circle with radius 50 This will create a smaller circle inside the larger one.
Is it possible to draw a circle of negative radius?
Radii are always positive. No, it is not possible to draw a circle with negative radius.
How do you draw the radius of a circle?
A line of any length may act as the radius of a circle. The radius is the distance from the centre to the perimeter of a circle.
How do you draw circle in qbasic?
In QBasic, you can draw a circle using the CIRCLE statement. The syntax is CIRCLE (x, y), radius, where (x, y) is the center of the circle, and radius is the radius of the circle. For example, CIRCLE (100, 100), 50 would draw a circle with a center at coordinates (100, 100) and a radius of 50 pixels. You can also specify a color by adding a third parameter, like CIRCLE (100, 100), 50, 15 for a circle in color 15.
How do you divide a circle into 8 equal parts using 3 lines?
Draw two diameters perpendicular to each other. Draw a smaller circle with the same centre such that the radius of the inner circle is 'r' and the radius of the outer circle is 'r√2.' [Or, the radius of the outer circle is R and the radius of the inner circle is R/√2.]
What is a radiu s of a circle?
If you draw a line from the center of a circle to the edge of a circle, you have drawn the radius of the circle. If you draw a line from the edge of a circle through the center of the circle and on to the edge on the opposite side, you have drawn the diameter of a circle. The radius of a circle is one half the diameter of a circle.
If i draw a circle that has a diameter of 2 centimeters what is the radius of the circle?
1 centimeter
How do you get a radius?
# Find the center of the circle # Draw the line of the radius from the center to the circumference # Finish
What does a chord look like in math?
When you draw a circle in math, and you draw a triangle inside of it, 2 of the lines should be the radius of the circle, and the third (bottom) line that is not the radius is the chord.
One radius of a circle is the same length as any other radius of any other radius?
The radius is the distance from the center of the circle to its edge. No matter how you draw this radius, it is one value of one length only, for any given circle.
Draw a flowchart to calculate the area of a circle?
The area of a circle is: pi times radius squared
How do you draw an arc in qbasic?
To draw an arc in QBasic, you can use the Circle statement, specifying the center coordinates, radius, and the starting and ending angles. The syntax is Circle (x, y), radius, start_angle, end_angle. For example, Circle (100, 100), 50, 0, 90 would draw a quarter-circle arc from 0 to 90 degrees centered at (100, 100) with a radius of 50.
How do you Draw Circles in GstarCAD?
The default method for drawing a circle is to specify a center point and radius.You can draw circles using any of the following methods:Center-RadiusCenter-DiameterTwo pointsThree pointsRadius-Tangent-TangentConvert Arc to CircleTo draw a circle by specifying its center and radiusDo one of the following:Choose Draw> Circle>center, radiusOn the Draw 2D toolbar, click the Circle Center-Radius tool.Type circle and then press Enter.Specify the center point.Specify the radius of the circle.
