0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many no of 16 mm rebar in 1 bondle of 2 ton?
188 nos.of rebar
What is the formula for rebar?
You have to find a chart that will indicate the weight per unit of measure for the appropriate rebar size. Than take that and multiply it by the the length of the rebar. For example, a #4 rebar weighs 0.668 lbs/ft. If you have 5 @ 20-00 pieces that is 0.668 X 20 X 5 = 67 lbs. Charts are available throughout the web or at CRSI.org.
How do you calculate rebar?
80% 3,425 lb
Formula for calculating rebar mass per kg?
You have to find a chart that will indicate the weight per unit of measure for the appropriate rebar size. Than take that and multiply it by the the length of the rebar. For example, a #4 rebar weighs 0.668 lbs/ft. If you have 5 @ 20-00 pieces that is 0.668 X 20 X 5 = 67 lbs. Charts are available throughout the web or at CRSI.org.
How much does 20' of 4 rebar cost?
between 4 and 6$ per stick.
How stirrups are fixed in Reinforcement for concrete slab?
I assume they would be tied using tie-wire to the rest of the rebar cage.
Do you have to pour all your concrete footings at once?
You should or at least each wall at the same time. You could pour it in sections as long as the rebar was joining each section. The problem would be at the joints. How to form up a section of the footing with the re bar in place. If the rebar is not tied together, the wall will move and never be what it should be.
How do you keep concrete block walls from collapsing?
Prior to stuccoing the CBS you can install metal mesh or REBAR
What is footings in construction?
It's usually the very base of a structure that bears and distributes the total weight of the building. It's usually concrete of varying thickness and width depending on the weight it has to carry and usually contains rebar for additional strength
Is rebar needed in concrete footings for posts?
If the posts are to support a structure such as a house or barn, yes. If the posts are to support a rail-fence, no. Check with your local municipality's code enforcement office for permit requirements. Then draw, draw, draw!
What is the cost per pound of rebar in Southern California?
.35/lb material .45/lb labor to install
What does a rebar fabricator do?
It can vary by fabricator but at minimum, a fabricator is responsible to fabricate the rebar, by cutting and bending as reqd for project. They usually will supply placing drawings for review and installation. Some may have install crews, but not all.
What is rebar detailing?
Rebar Detailing is a procedure of making shop drawings for the steel reinforcement for the development procedure. The Rebar Detailing procedure incorporates the position, bending shapes, amount, description, laps of the reinforcing steel and measurements. The Rebar Detailing Drawings are made to incorporate the separating, area, rebar size and lap of steel. The Rebar Detailing Services includes: Rebar Detailing Services, Rebar Shop Drawings Services, Rebar fabrication Services, Rebar Framing Plan Design, Rebar Structure Foundation, Rebar Pit Design, Rebar Framing Plan, Rebar Beam Design, Rebar Structure Steel Detailing, Structure Foundation Rebar Detailing.
What is rebaring?
Rebar Detailing is a procedure of making shop drawings for the steel reinforcement for the development procedure. The Rebar Detailing procedure incorporates the position, bending shapes, amount, description, laps of the reinforcing steel and measurements. The Rebar Detailing Drawings are made to incorporate the separating, area, rebar size and lap of steel. The Rebar Detailing Services includes: Rebar Detailing Services, Rebar Shop Drawings Services, Rebar fabrication Services, Rebar Framing Plan Design, Rebar Structure Foundation, Rebar Pit Design, Rebar Framing Plan, Rebar Beam Design, Rebar Structure Steel Detailing, Structure Foundation Rebar Detailing.
What is the unit of rebar 14mm?
The unit of measurement for rebar thickness, such as 14mm, is in millimeters (mm). This measurement refers to the diameter of the rebar.
How do you install a precast concrete wheel stop?
Concrete wheel stops are typically pinned into the paving using 18" long 3/4" diameter rebar.
What is the proper rebar configurations for concrete footings?
Depends on what the footing is holding. Typically, the reinforcing is place each direction in the bottom 3" of the footing. A top mat is sometimes required as is verical and horizontal bands, again dependent on the application required. The project engineer should have a designation of what and how much reinforcing is reqd.
