0
To set the time and date on an Ajanta ODC 170 clock, first, locate the "Set" button or switch on the back or side of the clock. Press and hold this button to enter the setting mode, then use the "Hour," "Minute," and "Date" buttons to adjust the time and date accordingly. Once you have made the adjustments, press the "Set" button again to save your changes. Make sure the clock is in the correct AM/PM setting if applicable.
What else can I help you with?
How do you set time in digital clock ajanta odc?
how to time set up ajantha degital clock model no: olc 103
Which is over dimensional cargo?
Over dimensional cargo (ODC) generally consists of Bridge sections (Pre-cast beams), Transformers, heavy machineries, Boilers, GAS turbines, Storage tanks, Heavy structure & the most important one is Windmill components (Blades, tower section & Motor Head).
How do you set the time in ajanta ODC-170?
Time sect
How do you set time in Ajanta ODC 120?
operating manual for ajanta quartz ocd 120
How do you set time in ajanta quartz odc-120?
operating manual for ajanta quartz ocd 120
How do you change time in ajanta quartz odc- 150?
The Ajanta Quartz ODC-150 clock has buttons at the side which allow the owner to set the time. Pressing these buttons in the correct configuration will enable this.
How can i set Day countdown in my Ajanta ODC-170 Clock?
To set a day countdown on your Ajanta ODC-170 clock, first, locate the "Mode" button and press it to switch to the countdown timer mode. Use the "Hour" and "Minute" buttons to set the desired countdown time. Once set, press the "Start/Stop" button to begin the countdown. Ensure that you monitor the display for any adjustments or completion of the countdown.
How do you set time in digital clock ajanta odc?
how to time set up ajantha degital clock model no: olc 103
How do change time in ajanta quartz odc -110?
To change the time on an Ajanta Quartz ODC-110 watch, pull the crown out to the second position. Rotate the crown clockwise or counterclockwise to set the correct time. Once set, push the crown back in to its original position to resume normal operation. Always ensure that the watch is not in water while adjusting the time.
How do you reset ajanta digital clock ODC-70?
To reset the Ajanta Digital Clock ODC-70, locate the reset button, typically found on the back or bottom of the clock. Press and hold this button for a few seconds until the display resets. You may then need to set the time and date according to the manufacturer's instructions. If there is no reset button, try unplugging the clock for a minute and then plugging it back in.
How do you set the time in ajanta ODC-110?
To set the time on an Ajanta ODC-110, first, locate the "Mode" button and press it until you reach the time-setting mode. Use the "+" and "-" buttons to adjust the hour and minutes accordingly. Once the correct time is displayed, press the "Mode" button again to confirm and exit the setting mode. Ensure to check AM/PM settings if applicable.
How do you set date month day temperature in ajanta quartz odc-70 model digital clock?
To set the date, month, day, and temperature on the Ajanta Quartz ODC-70 digital clock, first, press the "Set" button until the display starts blinking. Use the "Hour" and "Minute" buttons to adjust the settings for the date and month. For temperature settings, follow the same process, adjusting as needed. Finally, press the "Set" button again to confirm your changes.
How do you set date month day temperature in ajanta quartz odc-160model digital clock?
To set the date, month, day, and temperature on the Ajanta Quartz ODC-160 model digital clock, first, press and hold the "Set" button until the display starts flashing. Use the "Hour" and "Minute" buttons to adjust the time, then press the "Set" button again to switch to the date, month, and day settings, using the same buttons to make adjustments. Finally, if the model allows for temperature settings, follow the same process to set the desired temperature display. Ensure to save your settings by pressing the "Set" button one last time.
How do you set time in digital clock ajanta odc 40 youtube?
To set the time on an Ajanta ODC 40 digital clock, first, locate the "SET" button. Press and hold this button until the hour starts flashing, then use the "UP" or "DOWN" buttons to adjust the hour. Press the "SET" button again to move to the minutes, and repeat the adjustment process. Finally, press "SET" one last time to confirm the time setting. For detailed visual instructions, consider checking a tutorial video on YouTube.
