0
What else can I help you with?
Why do you turn the fraction upside down and multiply?
Dividing by a fraction is equivalent to multiplying by its reciprocal. A reciprocal fraction is effectively "turning it upside-down". So, to divide by a faction, you should do as stated; turn the fraction upside-down and multiply.
How does a prism reflect light?
It splits white light up into the colors of the visible spectrum, but if the colors go through another prism, they turn into white light again.
Why does a six looks like a nine and a nine looks like a nine?
Because if you turn a nine upside down then it does not look like anything but if you turn a six upside down then it looks like a nine.
What is the perfect square which will be still a perfect square if you turn upside down?
1
What would cause the overdrive light to flash on a 1999 ford windstar when you are doing about 55 miles per hour?
The light will flash if the vehicle senses that you should be in overdrive (based on speed) but aren't. There should be a button on the end of your gearshift lever to turn overdrive back on. The only time you should turn that off is, for example, if you are pulling a trailer in the mountains. Turn OD back on and the light will stop flashing. If it doesn't stop then there is a problem with the transmission going into overdrive.
How do you use the aux on a Pioneer Mosfet 50wx4?
Turn off the player, hold down the function button until it turns on taking you to a menu letting you set the time etc. Keep pressing the function until you get to the aux option, turn it on by pressing the up key. Then start the unit and press the mode button, you should now have CD, Tuner and Aux available. :-)
How do you operate a light switch to turn the light on and off?
To operate a light switch, you simply flip the switch up to turn the light on and flip it down to turn the light off.
How can you use your light switch?
To use your light switch, simply flip it up to turn the light on, and flip it down to turn the light off.
Construction of mosfet in depletion region?
To make a depletion MOSFET, the channel must be doped with carriers; this is in total opposite to an enhancement MOSFET which avoids carriers in the channel at all cost. (because the carriers in the channel become the subthreshold leakage current) Since you need to pinch the channel against the substrate to guarantee to turn off the channel completely, there must be a reverse bias between the substrate and the source terminal. As a result, the source terminal of an N type depletion MOSFET must be tied to Vdd. This is also a complete opposite to enhancement MOSFET. In order to turn off the channel quickly, the carriers in the channel of depletion MOSFET are usually planted shallowly. This is a drastically different from enhancement MOSFET that carriers must be planted deeply into source terminal in order to support a large diffuse current. The construction of depletion MOSFET thus requires far less diffusion time than enhancement MOSFET.
How do you turn off the M-CD source on a Pioneer DEH-P20?
For most Pioneer head units, you can hold down the SRC button until the unit turns off, then hold down the FUNC button until the menu appears. This is usually where you set the time as well as turn on/off M-CD or AUX inputs.
How do you operate a toggle light switch?
To operate a toggle light switch, simply flip the switch up to turn the light on and flip it down to turn the light off.
Can you demonstrate how to operate a light switch by turning it on and off?
To operate a light switch, simply flip the switch up to turn the light on, and flip it down to turn the light off.
Why is the light overheated?
you left the light for too long. turn it off for a while and it will cool down
How do you turn on valet mode for a prestige car alarm?
put key in ignition, turn to on position, reach down to flashing light button and hold down until light is a steady red.
How do you change the clock for pioneer keh-1750?
if it has the button function on it turn the headunit off and hold down function there should be a few options including the clock
How do you turn on a pilot light?
To turn on a pilot light, locate the gas valve and pilot light knob on the appliance. Turn the gas valve to the "pilot" position and press down on the pilot light knob while using a lighter or match to ignite the pilot flame. Hold the knob down for a few seconds to allow the pilot light to stay lit, then release the knob.
What must be done there is too much light that illuminates the specimen you are observing under the microscope?
Turn down the light.
