1. Calculate the surface area
2. Calculate the volume
3. Divide
Volume in cubic units = base area times length
You will have to work the surface area of one of the ends and then multiply that with the length.
The volume(cm3) of a tetrahedron is 1/3 (area of the base)X height
the ratio of surface area to volume of an object is inversely proportional. that is to say, when you make the object much larger, the amount of surface area to volume goes down. when you make the object smaller, the amount of surface area compared to the amount of volume goes down. consider a cube with equal sides of 2. The volume is 2x2x2 = 8. The surface area of each side would be 2x2 = 4. Times the 6 sides ... 4*6=24. So the surface area to volume ratio would be 24 to 8, or 24/8, or 3 now make the cube smaller with equal sides of 1. Volume is 1*1*1 = 1 Surface area is 1*1 per side = 1, * 6 sides = 6. Surface area to volume ratio is 6 to 1, or 6/1, or 6. you can work it the other way too and see i'm correct. so if you take a lumpy piece of chalk and grind it into a small powder, you have taken a larger single object and made it into countless incredibly smaller objects. since you're volume is unchanged, the amount of total surface area must be much greater in the powder.
Length times width times height = volume Or area times height = volume
You work both out from measurements of the shape and the relevant formulae.
The hot work ratio is the area ratio of the cast diameter and the pre-machined finished diameter.
How does the surface-to-volume ratio change each time you cut the value of "s" in half? 4mm 96mm2 64mm3 1.5 to 1 2.0mm 24mm2 8mm3 3 to 1 1.0mm 6mm2 1mm3 6 to 1 0.50mm 1.5mm2 .125mm3 12 to 1 0.25mm .375mm2 .016mm3 24 to 1
The rate at which the cell increases in size depends on the DNA. The ratio of the surface area (calculated: length x width x # of sides) is divided by the cell volume (calculated: length x width x height). THE VOLUME OF THE CELL INCREASES MORE RAPIDLY THAN THE SURFACE AREA, CAUSING THE RATIO OF SURFACE AREA OVER VOLUME TO DECREASE. This decrease causes cell malfunction. If the cell volume increases too much, then the ratio will decrease causing problems for the cell's regular functions.
Its volume is its cross-section area times its length.
volume=area of the cross section x the length
are both flat/thin and have folded membranes
Volume in cubic units = base area times length
You will have to work the surface area of one of the ends and then multiply that with the length.
The volume(cm3) of a tetrahedron is 1/3 (area of the base)X height
the ratio of surface area to volume of an object is inversely proportional. that is to say, when you make the object much larger, the amount of surface area to volume goes down. when you make the object smaller, the amount of surface area compared to the amount of volume goes down. consider a cube with equal sides of 2. The volume is 2x2x2 = 8. The surface area of each side would be 2x2 = 4. Times the 6 sides ... 4*6=24. So the surface area to volume ratio would be 24 to 8, or 24/8, or 3 now make the cube smaller with equal sides of 1. Volume is 1*1*1 = 1 Surface area is 1*1 per side = 1, * 6 sides = 6. Surface area to volume ratio is 6 to 1, or 6/1, or 6. you can work it the other way too and see i'm correct. so if you take a lumpy piece of chalk and grind it into a small powder, you have taken a larger single object and made it into countless incredibly smaller objects. since you're volume is unchanged, the amount of total surface area must be much greater in the powder.
hey, are you the physics160 student of Auckland uni? I just meet the question on my practice paper. square root of area / cube root of mass = ratio the ratio is always the same, so you can work out the answer for new area of 11.9 ( mass is poportional to volume not skin area.)