Q: How much does a lead .312 inch diameter by .5 inch long cylinder weigh?

Write your answer...

Submit

Still have questions?

Continue Learning about Math & Arithmetic

The weight (not mass) is 69.05 pound weight.

Rocks vary greatly in density and weight. A piece of pumice that size could weigh maybe an ounce, while a lead-laden rock may weigh many times that, maybe closer to a pound.

lead density is 0.41 pounds/cubic inch 1.68 x 0.41 = 0.688 pounds

l= .5 in d= .312 in dxdx .7854 x .5 = .0382269 cubic inches or .0000221 cubic feet multiplied by the known weight of lead (712 lbs/cubic foot) .0157352 pound lead cylinder

First find the volume, then multiply by the density of lead. Density of lead = 0.41 pounds per cubic inch.Volume = (area of base) * (length) = (pi * r2) * (length) = 3.14 * (0.75 in / 2)2 * (3 in) = 1.32 in3. Then (0.41 lb / in3) * (1.32 in3) = 0.54 pounds, or 8.6 ounces

Related questions

The weight (not mass) is 69.05 pound weight.

Rocks vary greatly in density and weight. A piece of pumice that size could weigh maybe an ounce, while a lead-laden rock may weigh many times that, maybe closer to a pound.

One cubic inch of lead weighs around 0.41 to 0.44 ounces.

The maximum amount of cylinder taper allowed in engine cylinders is typically around 0.001 inches per inch of bore diameter. Excessive taper can lead to poor piston ring sealing and increased oil consumption.

A lead brick typically weighs around 28 pounds per square inch, depending on its dimensions and density.

The density of lead is 11.34g per cubic centimetre. As there are 16.387 cubic centimetres in one cubic inch, one cubic inch of lead weighs 11.34 X 16.387 or 185.83grams. In ounces this is 6.55 (or just over 6 and a half) ounces.

The starter solenoid is the small (about 1 or 2 inch diameter) cylinder attached to the much larger cylinder that is the starter itself. This is usually located on the drivers side of the engine, low down and to the rear, attached to the transmission bellhousing. The positive battery cable will lead you straight to it, and attaches to the solenoid.

lead density is 0.41 pounds/cubic inch 1.68 x 0.41 = 0.688 pounds

l= .5 in d= .312 in dxdx .7854 x .5 = .0382269 cubic inches or .0000221 cubic feet multiplied by the known weight of lead (712 lbs/cubic foot) .0157352 pound lead cylinder

A US 25 cent piece, a quarter, is close to one inch in diameter; it is just short. Its diameter is just about 15/16 of an inch. The diameter of a circle is the length all the way across the face of the circle going straight through the center. So a quarter gives you a good estimate of a circle with one inch diameter. Just imagine a circle very slightly bigger across.If you take an ordinary lead pencil and trace a circle using a US quarter as your template, you'll probably come even closer to a one inch diameter circle. Test it out with a ruler handy so you can get a better sense of it.

First find the volume, then multiply by the density of lead. Density of lead = 0.41 pounds per cubic inch.Volume = (area of base) * (length) = (pi * r2) * (length) = 3.14 * (0.75 in / 2)2 * (3 in) = 1.32 in3. Then (0.41 lb / in3) * (1.32 in3) = 0.54 pounds, or 8.6 ounces

It's just a tad larger than the diameter of the lead in your standard yellow wooden pencil, and the same length as 3.3 millimeters.