answersLogoWhite

0

It will bend at any load greater than zero. It is just a question of how much. In your example the rod will bend 0.007 inches under 10 pounds, 0.07 inches under 100 pounds, etc.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Math & Arithmetic

How much weight will a four inch tall X 2 inch wide with a one quarter section steel tube five foot long supported on both ends hold in the middle without bending?

That depends... on the composition of the steel !


How do you make a square with 3 matchsticks without breaking or bending them in any way?

nn


What is bending radius for MICS cable?

The bending radius for MICS (Microphone Integrated Circuit) cable typically refers to the minimum radius that the cable can be bent without causing damage or degradation to its performance. This value can vary depending on the specific cable design and manufacturer, but it is generally recommended to maintain a bending radius of at least 10 times the cable's diameter. Adhering to this guideline helps prevent issues like signal loss or cable breakage. Always consult the manufacturer's specifications for the most accurate information.


How do you figure out the circumference of something without knowing the diameter?

If you know the radius, double that to get diameter. If you have neither radius or diameter, then measure around the outside.


How do you find the diameter without the circumference?

The diameter of a circle can be found without the circumference using the formula d = 2r. This formula requires that you know the radius of the circle which is half of the diameter. To calculate the diameter you need to multiply the radius by 2. For example if the radius of the circle is 4 then the diameter would be 8 (4 x 2 = 8).You can also find the diameter of a circle if you know the circumference. To do this use the formula c = d. By rearranging the equation you can calculate the diameter as d = c/. For example if the circumference of the circle is 12.5 the diameter would be 4 (12.5/ = 4).

Related Questions

What is the multiplier for 45 degree offset in conduit bending?

Back set for all conduit sizes is not the same. The greater the diameter of the conduit the length of back set increases. Without the diameter size of the conduit, an answer can not be given.


What is an example of flexibility?

An example of flexibility is bending over and touching your toes without bending your knees.


What is example of flexible?

An example of flexibility is bending over and touching your toes without bending your knees.


What is the ability to resist bending?

The ability to resist bending is known as bending strength or flexural strength. It is a measure of a material's ability to withstand bending without breaking. Materials like steel and concrete have high bending strength, making them suitable for applications where bending forces are common.


What is bending material without breaking it?

Forming, shaping or working.


How much weight will a four inch tall X 2 inch wide with a one quarter section steel tube five foot long supported on both ends hold in the middle without bending?

That depends... on the composition of the steel !


What is bending strength?

It is the maximum stress at which a material will fail when subject to flexural ( moment producing) bending loads. These stresses occur a the material outer fibers.


Does bending requires a heating process?

Bending can be done with or without a heating process. Heating metal, such as in annealing, can help make it more malleable and easier to bend. However, some materials like plastics can be bent without heating using techniques like cold bending.


Procedure of watch glass?

Glass bending procedure without dents


Why a person can't jump without bending legs?

To jump, you need the force of your leg muscles pushing off of the floor to move you into the air. Without bending your knees, you can't use your leg muscles.


Is stainless steel fireproof?

Stainless steel is not completely fireproof, but it is highly resistant to fire and can withstand high temperatures without melting or warping.


How do you remove sticky hooks without damaging the wall?

by removing it with cutting plyer without bending them or twisting them with a hammer