Unfortunately, limitations of the browser used by Answers.com means that we cannot see most symbols. It is therefore impossible to give a proper answer to your question. Please resubmit your question spelling out the symbols as "plus", "minus", "times", "equals".
There is no equation to solve!
(1) x + y = 15(2) x/y = 14Solving (1) and substituting in (2)...x = 15 - y15-y/y = 1414y = 15 - y15y = 15y = 1x = 14================================The sum of 1 + 14 = 15The quotient of 14/1 = 14
To draw a 16-to-1 demultiplexer, start by creating a box labeled "16-to-1 Demux" with one output line and 16 output lines. Connect 4 select lines (S0, S1, S2, S3) to the input of the demultiplexer to control which of the 16 outputs is activated. Draw the 16 output lines branching from the box, labeling each output from Y0 to Y15. Finally, indicate that the single input signal is fed into the demultiplexer, which directs it to one of the 16 outputs based on the selected input combination.
(y10 + 2y5z3 + 4z6)
You get the coordinates by asking the queen, and they are x73 y83, x15 y15, and x83 y20.
No,you can't land on the sun. But You can land on: X73 Y83 , X15 Y15, and X83 Y20.
The question does not specify what x and y measure. It is, therefore, impossible to answer the question.
Unfortunately, limitations of the browser used by Answers.com means that we cannot see most symbols. It is therefore impossible to give a proper answer to your question. Please resubmit your question spelling out the symbols as "plus", "minus", "equals" etc. Also use ^ to indicate powers (eg x-squared = x^2). There is no equation (equality symbol) and no symbol between y and 15.
(1) x + y = 15(2) x/y = 14Solving (1) and substituting in (2)...x = 15 - y15-y/y = 1414y = 15 - y15y = 15y = 1x = 14================================The sum of 1 + 14 = 15The quotient of 14/1 = 14
yes you can but will need to make new wires to got to speedo signal and fuel gauge if the wires are not there. would need a gray plug, This is the wire code for gray plug. grey connector info, in the brackets is the equivalent earlier MID pin info (Y=Yellow con and B=Black con) Pin1(Y2) - Brown - To Chassis (0V) Pin2(Y3) - Blue/White stripe - Outside temp sensor Pin3(Y4)- Blue - Outside temp sensor Pin4(Y5) - Black - To F15 (15A) Pin5(Y1) - Red - To F12 (20A) Pin6 - Green - RPM signal, needs to be conecter to dash. Pin7(Y7) - Grey/Yellow stripe - Instrument Illumination (dimmer controled) Pin8(Y8) - Red/Grey(white) Stripe - Radio (aerial power feed i.e. Radio on indication) Pin9(Y9) - Brown/White Stripe - Radio Serial Interface Pin10(Y10) - Brown/White Stripe - Radio Serial Interface Pin11(Y11) - Brown/White Stripe - Radio Serial Interface Pin12(B8) - Blue/Black Stripe - Fuel level sender Pin13(B11) - Brown/Grey Stripe - Oil level sensor Pin14(Y14) - Brown/White Stripe - To pin 8 of diag connector (to support programming) Pin15(Y15) - Black/Yellow stripe - To check control Pin16(Y16) - Black - To F2 (15A) Pin17(Y17) - White/Green stripe - To check control Pin18(Y18) - Black/Yellow stripe - To check control Pin19(Y19) - Yellow/Red stripe - To brake pad wear sensors Pin20 - NC Pin21(Y23) - Grey - To Auto transmission Pin22(B10) - Brown/Yellow Stripe - Washer Level sensor Pin23(B5) - Brown/White Stripe - Computer stalk buttons Pin24(B6) - Brown/Red Stripe - Computer stalk buttons Pin25 - NC Pin26(Y12) - Blue/red stripe - Speed signal (from ABS controller) Pin27(B9) - Black/Brown Stripe - ECU signal Pin28(B3) - Brown/Blue stripe - Coolant level sensor Pin29 - Black/Violet Stripe - To Hid lighting Pin30 - To Diesel fuel pump (X20DTH only)